What I finally found out was that if you use a blue/red connector ecm you had to use a TAC/Pedal assembly from a Corvette. The vetts have 2 sensors in the pedal assembly but the truck pedal assembly...
Type: Posts; User: camaro68; Keyword(s):
What I finally found out was that if you use a blue/red connector ecm you had to use a TAC/Pedal assembly from a Corvette. The vetts have 2 sensors in the pedal assembly but the truck pedal assembly...
I have figured out the problem with the DBW. I was using a Red/Blue ECM and a TAC and Throttle body from a Green/Blue ECM. Once I reflashed a Blue/Green ECM it started working correctly.
I have a LQ4 was a DBC but I converted over to a DBW with a TAC controller part number 12588923 and its pedal assembly. It works till it hits 85% throttle and then it closes the throttle blade and...
I was able to convert the harness and ecm over to a DBW with a doner TAC and pedal assembly. Now my biggest problem is at 85 percent throttle the Throttle blade snaps shut and you have to power...
I have a 6.0L and a 4l80E that is going into a 49 Caddy and was wanting it to be a DBW instead of a DBC setup. I have the ecm that came with the engine and its a 12200411 ecm is it possible for it...
General question about control modules. Can the V2 flash tool be used to replace defective units with new ones or can this only be done by dealers? I am assuming modules like the Fuel Pump Control...
Here are both the ecm and tcm files.
Thanks for the help. After installing the new T42 in the car I cannot get the speedometer to work in the Corvette. I can see the speed on the dashboard of EFILive but not in the car. Is this...
How do you change the OS of a t42 module. Or is it even possible and if so where do you find the files at?
I did a full flash but i got an error saying the OS was different on the New one compared to the old one.
I am trying to put a new T42 Module in a 05 Corvette, but i cant figure out how to program it. I have tried copying the VIN into the controller but i cannot get the controller to take the VIN. I...
I am new to actually "tuning" a modified engine. I have used EFI Live to disable the VATS and other systems for engine swaps into older cars, but now I am wanting to actually help tune a 2001 vette....
I am new to actually "tuning" a modified engine. I have used EFI Live to disable the VATS and other systems for engine swaps into older cars, but now I am wanting to actually help tune a 2001 vette....
After you flash a ECM with V8 how do you edit the program again since V7 will not open a V8 tune.
It was purchased off of the web store from your website. How do I go about returning it for the GM version?
but I have two vin license that have not been used.
I saw that so how do I get it activated?
Here are some of the screen shots of what is going on I hope they help.
1601316014160151601616017160181601916020
Here are some of the screen shots of what is going on I hope they help.
1601316014160151601616017160181601916020
I am using version 8.2.2 build 234. I have licensed the controller and tried to flash it but it comes back and says controller must be license. I have checked and I am using Boot block version...
What has to be changed in the tune to make the engine/transmission work in another vehicle.
What does it take to take a LS ECM and turn it into a standalone PC with factory harness or an after market harness.
I have read a pcm from a 4.8 LS truck and have deactivated the VATS, but now I cannot get it to reflash into the PCM. It says I have no license to do it but I have 2 VIN license left. Any ides on...
Where can I purchase the V8 software and do I need a programmer to reflash GM ECU's.