Search:

Type: Posts; User: ChipsByAl; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    169

    Good job Erik! Al

    Good job Erik!
    Al
  2. Replies
    9
    Views
    169

    2001 Express Van file

    Here is an Express Van file for 2001 with the 5.7.
    Al
  3. Replies
    1
    Views
    416

    Post your tune and DTC's set. Are you using the...

    Post your tune and DTC's set. Are you using the V-6 distributor with the V-8 cap?
    Al
  4. Replies
    7
    Views
    547

    What about streams? Al

    What about streams?
    Al
  5. Replies
    5
    Views
    534

    Joe it uses an E38

    Joe it uses an E38
  6. Replies
    1
    Views
    123

    That looks like the old design MAP sensor from...

    That looks like the old design MAP sensor from the 80's or 90's. Not sure of the scaling on one compared to the new design sensors. If you can't get it worked out with manual testing Holley does...
  7. Replies
    7
    Views
    434

    What kind of vehicle is it?

    What kind of vehicle is it?
  8. Sticky: It runs windows 7 Pro Al

    It runs windows 7 Pro
    Al
  9. Sticky: Hi Paul, my last update was from October 2018...

    Hi Paul, my last update was from October 2018 (Version 7.5.24), been a while. Anyway thanks for the "tun" file fix. My problem has been closing the program. If I use the "X" in the top right corner I...
  10. Replies
    3
    Views
    533

    Its not the km/H causing you the problems, its...

    Its not the km/H causing you the problems, its because the reluctor tooth count is incorrect. Check the speedo section of the donor OS file and you will see that H0102 is 40 and yours is at 17....
  11. Manual or auto? You can also try here:...

    Manual or auto? You can also try here: https://www.dropbox.com/sh/4ydh5wltk3ssxbw/AABfLhrwk_9cnvNKa9pcXuoea/Corvette?dl=0&subfolder_nav_tracking=1
    Al
  12. Interesting project, Ponrov. What vehicle did the...

    Interesting project, Ponrov. What vehicle did the harness come from? Or did someone build it for you? Is there a 4L60 to 4L80 adapter getting used?
    Al
  13. Replies
    2
    Views
    288

    You might need to change units on the device....

    You might need to change units on the device. Look at page 31 in the manual.
    Al

    PS. I don't have one of these, I just looked at the manual....
  14. Replies
    11
    Views
    921

    Thanks for sharing. Al

    Thanks for sharing.
    Al
  15. Well you know what will work for sure! Nowadays...

    Well you know what will work for sure! Nowadays harnesses can have subtle differences that need to be checked pin for pin. Since you have the adapter, that's the way I would go.
    Al
  16. Replies
    6
    Views
    626

    Keep the MAF if you can and put the stock MAP...

    Keep the MAF if you can and put the stock MAP sensor with a good grommet in the hole where the MAP sensor goes. That will get you in a better place to start tuning. There are tutorials here on the...
  17. Replies
    6
    Views
    626

    I'm not sure of the design of the intake...

    I'm not sure of the design of the intake manifold, but I would strongly recommend against running a 3-bar sensor on a normally aspirated engine. You will lose 2/3 of the VE table resolution. You...
  18. Replies
    6
    Views
    626

    Did you change the map sensor because you are...

    Did you change the map sensor because you are planning on using boost? If so it would be best to convert to the later model PCM.
    Al
  19. Replies
    6
    Views
    819

    Glad you got it sorted. It’s a shame that...

    Glad you got it sorted. It’s a shame that sometimes the aftermarket doesn’t pay attention to details like that.
    Al
  20. Replies
    6
    Views
    819

    Is the rotor correctly orientated? You need to...

    Is the rotor correctly orientated? You need to check the plastic pins on the bottom of it, making sure they line up with the pins in the shaft. If the rotor can go on either direction, (not sure...
  21. Replies
    17
    Views
    2,637

    Try to get your tuner to post the file that he is...

    Try to get your tuner to post the file that he is using.
    Al
  22. Replies
    17
    Views
    2,637

    So you probably don't have a correct crank...

    So you probably don't have a correct crank signal, incorrect software in the PCM or bad PCM. You definitely have something coming out of the crank sensor and wiring. Can you use the scan tool and...
  23. Replies
    17
    Views
    2,637

    Fuzzman sorry I could not get to you sooner, been...

    Fuzzman sorry I could not get to you sooner, been busy. Your first post has a few points I need to go over to be sure we are on the same page.

    You have a "beautiful, square signal on the scanner"...
  24. Replies
    17
    Views
    2,637

    The PCM does not have to be out of a van. Any one...

    The PCM does not have to be out of a van. Any one with the correct part #'s including the 9354896 can be used. The software including the Operating system and the Calibrations are more specific. Can...
  25. Replies
    2
    Views
    927

    This may work for you. It is not a DBC file...

    This may work for you. It is not a DBC file though.
    Al
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4