Search:

Type: Posts; User: driver456; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    118
    Views
    30,884

    I contacted Moates the other day in a e-mail,They...

    I contacted Moates the other day in a e-mail,They said about 2 weeks for a 0411pcm Roadrunner
  2. I know this thread is old but I was searching for...

    I know this thread is old but I was searching for something and ran across this.Do not use Dex 6 or any other synthetic trans fluid in a 700r or 4l60e, I had best results with Valvoline Dex III trans...
  3. Replies
    0
    Views
    656

    Any way to stop this warning

    18476
  4. Replies
    0
    Views
    1,208

    2007.5 lmm duramax

    i read the tune every thing worked but when i go to edit in the v7 tune tool on the left side every thing says unknown under calibrations.Never mind got it working.
  5. Thread: 2007.5 lmm

    by driver456
    Replies
    0
    Views
    983

    2007.5 lmm

    i read the tune every thing worked but when i go to edit in the v7 tune tool on the left side every thing says unknown under calibrations.Never mind got it working.
  6. Replies
    37
    Views
    13,243

    I know this thread is old but I can't get the...

    I know this thread is old but I can't get the boost ve table to work with rtacs.Any idea's? I updated the cal link.*UPDATE* Got it working,Figured it out.I was changing the wrong cal_link.
  7. Replies
    13
    Views
    3,434

    I got it Joe,Made changes in the sae generic...

    I got it Joe,Made changes in the sae generic text.The reason I wasn't seeing any changes was I had to diconnect the scan tool and reconnect and I saw the changes in the volts and a/f.
  8. Replies
    13
    Views
    3,434

    I found some old posts and copied from them into...

    I found some old posts and copied from them into the sae generic and calc pids I have it close now.Its .50 low on the a/f and .25 on the volts.Volts are showing 4.75 when it should be 5.00 and the...
  9. Replies
    13
    Views
    3,434

    There is no adjustment on them.I'm going to hook...

    There is no adjustment on them.I'm going to hook up my V2 today and see what happens.
  10. Replies
    13
    Views
    3,434

    Joe,I did the AA battery check,It was dead balls...

    Joe,I did the AA battery check,It was dead balls accurate in the scanner.I checked the battery with a DMM,It was 1.33 volts and the scanner was 1.33v.Then I connected the 2 AA batteries together and...
  11. Replies
    13
    Views
    3,434

    OK Joe,Thanks.I will try tomorrow.

    OK Joe,Thanks.I will try tomorrow.
  12. Replies
    13
    Views
    3,434

    Thats the pid I've been using

    Thats the pid I've been using
  13. Replies
    13
    Views
    3,434

    What do you have to change? No matter what number...

    What do you have to change? No matter what number I changed in the sae_ generic text it still stayed the same. I'm having the same problem with my plx.The gauge is showing 14.7 and in the scanner its...
  14. Replies
    52
    Views
    16,949

    Thats what I have on the vette,A NW102mm TB.I ran...

    Thats what I have on the vette,A NW102mm TB.I ran the car a few times at 100% throttle,But only about 10# of boost and it ran fine.Soooooooo maybe you have to get your self a NW TB before you pull...
  15. Replies
    52
    Views
    16,949

    If you want to try one more thing,Put a bigger...

    If you want to try one more thing,Put a bigger pulley on and lower the boost and see if it goes into REP.Other than that,You probably have to go to a cable TB.
  16. Replies
    52
    Views
    16,949

    Good idea

    Good idea
  17. Replies
    52
    Views
    16,949

    Did you update your efilive yet?

    Did you update your efilive yet?
  18. Replies
    52
    Views
    16,949

    Have you tried the stock 78mm TB with the factory...

    Have you tried the stock 78mm TB with the factory harness/wiring? I would still update your EFILive.
  19. Replies
    52
    Views
    16,949

    I read your 1st post again.You are using a X-LINK...

    I read your 1st post again.You are using a X-LINK What is it and what does it do and why are you using it.OK never mind,Looked it up,TB adapter.What TB was on the truck before the SC and what pcm are...
  20. Replies
    52
    Views
    16,949

    Just for the heck of it,Try scaling your injector...

    Just for the heck of it,Try scaling your injector flow rate downward about maybe 25%,You would also have to minus 25% off your VE table also.Do you tune your truck or does somebody else?
  21. Replies
    52
    Views
    16,949

    Did you update efilive? There was a "bug" awhile...

    Did you update efilive? There was a "bug" awhile back that affected the throttle tables.I see in your log that the throttle % is moving around a bit.You might have to go with a cable TB.Boost...
  22. Replies
    52
    Views
    16,949

    Give me some time,I'm looking at it now.Also...

    Give me some time,I'm looking at it now.Also check your throttle blade by hand @ WOT the blade should be at a 90 degree angle,See if it goes past that.Mine did,And If I remember I drilled a hole and...
  23. Replies
    52
    Views
    16,949

    Copy and paste these tables that I changed from...

    Copy and paste these tables that I changed from your tune.They only have to do with ETC & TP Look them over first if you want. C6102-C3906 The next one's are the RED FOLDER B2706-B2713-B2717-B2702 It...
  24. Replies
    52
    Views
    16,949

    Post up or send me one of your logged runs where...

    Post up or send me one of your logged runs where it goes into REP.If you can log a run where you just roll the throttle on up to WOT
  25. Replies
    52
    Views
    16,949

    In post #18 you say your going into REP mode,Now...

    In post #18 you say your going into REP mode,Now in post #20 your not getting any codes that puts you in REP mode.There is other ETC tables that have to be adjusted.Awhile back there was a problem...
Results 1 to 25 of 302
Page 1 of 13 1 2 3 4