Thanks. I was afraid of that. I'll call Wait4ME Performance tomorrow to see what they can tell me.
I appreciate the help. And thanks killerbee for the offer to put it on the bench. I'll probably...
Type: Posts; User: jeeper; Keyword(s):
Thanks. I was afraid of that. I'll call Wait4ME Performance tomorrow to see what they can tell me.
I appreciate the help. And thanks killerbee for the offer to put it on the bench. I'll probably...
Hello. I recently (within the last 2 months) bought a 2004 Silverado LB7 that needed new injectors. I have since replaced the injectors and the truck runs ok now. My problem is I now have a security...
Another follow up. The engine did finally start. It took lots of persistence. I never cranked the starter over for more than 15-20 seconds at a time and only did that up to three times consecutively...
Another quick update. I figured since I may actually be getting close to a running engine I should probably change the oil before it fires up. The oil in the engine was black and unknown age. I had...
I'm in updating this thread while I'm chomping at the bit...I'm letting the starter cool down. I'm starting to see some white smoke coming from the exhaust. It's very tempting to keep going but I...
So is this an indication I may need an injection pump?
I hooked up my V2 today to see what I could see. I took some screen shots of the DTCs
I do want to state here that I realize I may have the wrong accelerator pedal but it does seem to be reading...
Thanks again.
So I have verified my wiring. My wiring harness appears to match the harness document. All the switched and unswitched positive wires are connected to battery positive and the ground...
Thanks kidturbo. I really appreciate the help. I may end up sending a PM but I'll post the questions here just in case any information given may help someone else in the future. These forums are...
I found a pinout for a 2007 Lmm. I have read it is the same as the 2006 LBZ. When I compare the 2008 LMM it shows pin 56 on the 58 pin connector as D-Bu Accessory Wake-Up whereas in 2007 pin 56 of...
I don't have any relays with my harness. I got the harness without any fuse blocks or relay stuff. It only had the plug which I believe is called C2. It had the orange and pink wires on it. For now I...
Thanks.
I know the E35A is for LLY and LBZ and the E35B is for LMM but I'm wondering if the E35B could be flashed with a E35A OS and operate a LBZ engine? And If it can, is it able to be done with EFI Live...
Not sure if you're monitoring this but I am in the process of doing something similar I think. Did you ever get it going?
I'm trying to do a 2006 LBZ using just the engine and transmission...
I just wanted to say thanks to everyone who helped me get this going. It has been running beautifully for a while now. In fact I had an offer to buy the vehicle so I ended up selling it. Time to...
Time for another update and some more questions.
So I will start out by admitting I still don't know much about EFI but I have learned some things that have helped. First off I was not aware that...
So time for another update.
I still don't really "understand" what I'm doing but I hope I'm getting closer to that.
I played around quite a bit yesterday and had many unsuccessful attempts. I...
Thanks for the reply. I think I have it going now though.
I was (and am) getting good readings from the gauge.
My problem was setting the gauge set up correctly in the software. Actually...
I think I may have it. I'll report back tomorrow with details. Otherwise I'll report back in frustration...
So I found a calc_pids.txt in another forum that has a completely different calculation for BEN. I'm wondering if I'm supposed to be dividing instead of multiplying in my equation?
#...
I'd be happy to if I knew how. I'm still trying to learn how this all interacts and thus is why I'm struggling with this so much I guess.
Until I figure out how to make the map can I just look at...
So I have been trying to tune with the AEM 30-0334 with an analog connection to my V2. I have tried several calc_pids.txt files but don't seem to be getting correct output to adjust my VE table. I'm...
I'm guessing I still don't have a proper formula.
Thanks Bob. I was just in process of reading how to create the pids using the Auto VE tutorial. It spells it out pretty good so far.
One thing I noticed when I put your file in place was an error...
This is my current calc_pids.txt. I am renaming it and attaching it here so I don't get confused by it.
I'm wondering if I don't have the proper understanding of how this works. My 30,000 foot...