Search:

Type: Posts; User: mecnic99; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    2,734

    sorry for the late reply, the issue was a...

    sorry for the late reply, the issue was a restricted fuel line. Repaired that and the tune came in near perfect.

    Thanks for the help!
  2. Sticky: Yes

    Yes
  3. Sticky: No I'm not sure it's running on the v.e only. I...

    No I'm not sure it's running on the v.e only. I have maf signal disconnected p0101 no error, p0102 no mil and p0103 no mil, and fail frequency set to 150 so it should be v.e. only. Yes the o2s switch...
  4. Sticky: So I have this all set up, now it leans out my...

    So I have this all set up, now it leans out my stft to the point it will barely run. My o2 show 800-1000mv which should be rich and the reason it keeps subtracting from my v.e.table. I have it set...
  5. Replies
    25
    Views
    25,740

    Sticky: i know this is an old thread, but has anyone...

    i know this is an old thread, but has anyone tried to use a road runner on v8? i have yet to figure out how to put in my key to activate it, i show the cummins and tune upgrade but not the road...
  6. Replies
    11
    Views
    2,734

    I made the changes that Joecar mentioned and the...

    I made the changes that Joecar mentioned and the problem is still there, I installed a different tune from a nearly identical setup and the lean condition is still there. At this point, I think the...
  7. Replies
    11
    Views
    2,734

    no it is s/d and I won't be able to log it again...

    no it is s/d and I won't be able to log it again until the weekend.
    can't believe I didn't see this.
  8. Replies
    11
    Views
    2,734

    sorry for the delay but here is the tune file.

    sorry for the delay but here is the tune file.
  9. Replies
    11
    Views
    2,734

    lean at wot snap in gear

    This is a 5.3 with a asa 525 cam. the issue is a constant lean condition under a wot snap from idle. I have added up to 30% more fuel in the v.e. table and it has had no effect. this a s.d.tune. if...
  10. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    hey joe, i was looking and reading the user note...

    hey joe, i was looking and reading the user note in A0011 and it reads that this is used on (j2,pin56) shouldn't it be C2,pin 56?

    I fixed all oor cells along with B3647, hopefully when it warms...
  11. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    cos is now loaded and cal is flash in. read the...

    cos is now loaded and cal is flash in. read the file and the cos is there. adjusted what I needed and now ready to tune.
  12. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    ok so running as administrator is the fix. i...

    ok so running as administrator is the fix. i wasn't getting the 3-4min programming process of the flash before and it works fine now. still shows flash fails but it's after the reprogramming phase of...
  13. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    16619 i'm also getting this error also.

    16619 i'm also getting this error also.
  14. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    I think i have something different going on that...

    I think i have something different going on that what #11 is refering too.
  15. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    1661716618 this what i get everytime i try to...

    1661716618

    this what i get everytime i try to full flash the cos02020003
  16. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    under stand that much. but is won't complete the...

    under stand that much. but is won't complete the full flash of the cos..

    screen shot how too??
  17. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    that's was what i had done. tried again...

    that's was what i had done.

    tried again tonight.

    i started from the 12212156 cal full flashed(not problems) then full flashed 02020003 and the flash gets almost the end and fails. if any of my...
  18. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    12212156 os and tried using (trying to recall but...

    12212156 os and tried using (trying to recall but I think it is) cos 02020003 and 05. I am running v7.5.7 software.. I found the cos in the tutorial that corresponds with my os. not sure what is...
  19. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    i performed a full flash and it failed. then i...

    i performed a full flash and it failed. then i flashed stock cal. and read it out of curosity and it shows ve to be in psi and rpm. this what i would expect accoring to all i have read. is this...
  20. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    thank you Taz. new to this software and i seem to...

    thank you Taz. new to this software and i seem to get lost in the forums.
  21. Thread: cos help

    by mecnic99
    Replies
    28
    Views
    4,279

    cos help

    I'm trying to build a cos for a boosted 6.0. I have read the file and I don't have an option for a cos. do I have to perform a full flash before this will become available. I'm using a operating...
Results 1 to 21 of 23