I have attempted to flash a 19 5500 and it fails with a checksum error at the end. I was unaware of the new updates on these trucks. I'm looking of for the stock file to try to recover this truck....
Type: Posts; User: trudynosports; Keyword(s):
I have attempted to flash a 19 5500 and it fails with a checksum error at the end. I was unaware of the new updates on these trucks. I'm looking of for the stock file to try to recover this truck....
I attempted to flash a 2011 GMC express van today. The flash appeared to finish correctly but the truck wouldn't start afterwards. I tried to do a full flash of the stock read back in and it...
Trying to add a flex fuel sensor to a 2016 GMC Sierra Denali. Set everything up correctly and it wouldn't work. After trying several things including a full flash, I used another software to read...
Do we know if there is any other 2.2L 4cyl that is currently supported that I can use for this PCM? I just need to make a minor change and it's a base 2.2L manual with zero options.
1164611647
I have two here that are not supported
Thanks guys, that is what I was thinking but I wanted some input before I did the full reflash.
I read the stock file out and it had all checksums disabled. I ran the checksum fix and reflashed. The car runs fine but does not appear to be accepting any changes like idle speed etc... I read...
My fault, I was looking at an E38 as I was typing the post, lol. The ECM I couldn't unlock had the three connectors and datalogged perfect with my E40 PIDS. I'm thinking of swapping in a production...
I tried to calibrate a GMPP LS2 kit this past weekend and could not read the ECM. Wrong seed/key? The ECM was mounted up under the street rod and not easily visible but I showed the guy an E40 ECM...
Restarting/Rebooting fixed it. I've never seen this happen before but I'll know next time. Thanks everyone for the help.
I am working with an 02 2.2L 5spd. I licensed the PCM like normal and when I went to flash the PCM I got another message saying it is not licensed. I looked at the V2 license list and it took one...
Anyone got a transmission file for this car?
Thanks, I shall give it a shot tomorrow.
I read out a stock 06 Pontiac Solstice today. The read went fine and the stock file is attached. Went back out to the car about 15 mins later and started it up to leave and the check engine light...
Thanks a ton!
I need an 08 LS3 Stock tune file as well. Went by my local dealer but the ony LS3 they had on the lot was an 09 with different unsupported OS.
Update:
I'll get some graphs up soon,
The truck is now making 445/490 with a Whipple on 9lbs. Still stock 5.3 with only a camshaft and exhaust. I finished the SD tune last night with the...
Be careful about removing any fuel to bring the AFR's back up when spraying the meth. Meth of course has less energy and stoich is a lot lower than gasoline so let stay on the rich side. I run...
There a lot more than $200.00. Most of them still need TPS and VSS at minimum. They usually run in the $800.00 - $1200.00 range.
First of all it sounds like you may have an O2 issue. You didn't mention whether you were in OL or not so I would put the car in open loop and see if it stops leaning out. Then, if your going to...
I tried to flash truck and got bootloader failed. Tried in slow mode and same thing. Test fails the same way. I'm not sure what's going on but the PCM will read just fine. Any ideas?
Thanks,
Got another one for you too if you've got the time. I'll send another email.
Thanks again,
Thanks,
I think I sent you a couple a week back, I'll resend them. What email should I be using? Thanks,
Since were still waiting on calibration files, if anyone has a stock calibration from a 98 S-10 2.2l that did not have an EGR please post for me. I need to delete the EGR on one and would like to...
With the 03 OS you shouldn't have to worry about retuning the 105kpa and below if the original MAF included tune was mapped correctly. The VE should have already been mapped independent of the MAF...