Search:

Type: Posts; User: slow89irocz; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I am going to make a connector that will allow me...

    I am going to make a connector that will allow me to put a resistor in place to simulate the solenoids. From pins E to T, E to S, and E to A I will use a 22ohm resistor. From Pins E to U and E to B I...
  2. Yep when I took it for a test drive last night I...

    Yep when I took it for a test drive last night I had pins R and P grounded and a 660ohm resistor for the temp sensor. All the TSTATE09 bits were no. However it was strange that the GEAR PID went from...
  3. I tried to use the 4th gear switch but it locks...

    I tried to use the 4th gear switch but it locks too soon really lugs the engine. 3200rpm stall converter. Thats why I want to get the PCM involved so I can control the mph it locks at.
  4. Looking at trouble code P1810 which is a valve...

    Looking at trouble code P1810 which is a valve switch malfunction. It will assume D4 and enable the TCC lockup inn commanded 4th gear? I will turn on P1810 process enablers and see what happens....
  5. Went for a test drive. As soon as I stat moving...

    Went for a test drive. As soon as I stat moving all the Tstate09 flags go to NO but the gear PID changes from 3 to 1 so its thinks I am stuck in 1st? No lockup.
  6. could the tcc off due to downshift be yes since i...

    could the tcc off due to downshift be yes since i am testing with the car not mving...vss=0?
  7. I tried grounding pins N P R on the trans...

    I tried grounding pins N P R on the trans connector and with nothing grounded it says gear 2 and tcc off due to range is yes. Grounding any other combo only yeild a gear 3 and a tcc off due to...
  8. ok thanks

    ok thanks
  9. ok thanks for checking on the patch..

    ok thanks for checking on the patch..
  10. ok i am really getting confused here....

    ok i am really getting confused here....
  11. Also is there a patch for the tuning software...

    Also is there a patch for the tuning software that can add the tcc lockup temperature tables so I can get rid of the resistor?
  12. I do have a 4th gear switch that is already...

    I do have a 4th gear switch that is already routed to the tcc connector on the trans. can I feed this into the PCM? what combo of pins need to see ground to indicate 4th?
  13. Ok I was thinking it was the gear selector input...

    Ok I was thinking it was the gear selector input that was refered to as range. How do I fool the PCM into thinking it is hooked to the manual valve presure switches? Can I ground on pin and it will...
  14. I have the p/n position input being grounded by...

    I have the p/n position input being grounded by my shift lever switch and PID PRND shows P and D4 when selected. Also TCC brake is connected and shows depressed and released with the brake pedal....
  15. I believe it has to due with pins c1-32, c1-34,...

    I believe it has to due with pins c1-32, c1-34, c1-72, c2-62. In the harness 32 and 34 are connected to my shift lever switch which grounds them in park/neutral. What is needed for pins 72 and 62?
  16. Joe I still get the tcc off due to range..what is...

    Joe I still get the tcc off due to range..what is this? I placed a resistor and the tcc off due to temp is off now..
  17. Can I put a resistor between pins on the ecm for...

    Can I put a resistor between pins on the ecm for the temp sensor...but what is the range error?
  18. monitoring tstate9 says that the tcc is not...

    monitoring tstate9 says that the tcc is not locked due to cold transmission and due to range.
  19. Anyway to fool 411 PCM into thinking its connected to 4L60E for TCC operation?

    I did a 411 PCM swap in an 89 camaro and I want to use the PCM to control the TCC on a 700R4. I have the TCC enable soleoid wire (pin 42) wired to the TCC lockup solenoid. I can command it to lock...
  20. Help.....EFI LIVE????:doh2:

    Help.....EFI LIVE????:doh2:
  21. EFI Live PID CMPRET reporting incorrectly

    0411 PCM. Got a constant code of P1345 (cam crank correlation error). PID for cmpret is reporting -45.xx degrees. Car starts and runs. Distriutor cant be out that much. Any ideas.... :shock:
  22. Replies
    2
    Views
    2,005

    I am thinking that the efilive pid must be...

    I am thinking that the efilive pid must be reporting wrong since then 2002 express van used a 4x relucor ring not a 24x like it states in places in the tuning software. So since I have 4 pulses and...
  23. Did you ever get this to idle? If so what does...

    Did you ever get this to idle? If so what does PID cmpret say at idle.
  24. Replies
    2
    Views
    2,005

    p1345 help??

    Stabbin in a new dizzy, started car a few times no p1345. ...just threw a new code P1345. I loaded the CMPRET PID and it shows a value of -44.XX degrees... How can I be out that much. I had the...
  25. Replies
    3
    Views
    3,964

    does EFI live do anything after the CASE button...

    does EFI live do anything after the CASE button is pressed? I hit it and nothing at all happens
Results 1 to 25 of 30
Page 1 of 2 1 2