Search:

Type: Posts; User: TuneMaster; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Little bit fat for my liking, I normally aim for...

    Little bit fat for my liking, I normally aim for around 11.8:1 at the engine pipe and even this can be a tad bit rich but very safe. If its stock and depending on boost you can run 14-15 deg timing....
  2. Replies
    2
    Views
    2,449

    Thanks for posting those up, I saw them on Tune...

    Thanks for posting those up, I saw them on Tune File Depot and was wanting the files with the exact segments as well as os, the ecm is very close and I will try it.
  3. Replies
    2
    Views
    2,449

    E38 and T43 stock files required.

    Hi Guys,

    I'm after stock E38 and T43 files with the following OS's

    VIN 6G1EP55H37Lxxxxxx

    E38
    Control Module Calibration Release - Initial Release
    Service Pack 1
    12612381 Main Software...
  4. Replies
    69
    Views
    58,628

    I've had a 4l80 in a VE Calais for 8 months now...

    I've had a 4l80 in a VE Calais for 8 months now using E38 and T42 all working on can bus and fully functional. Had to make auto wiring loom from scratch. Even used a 4l80 file for the T42 which i...
  5. Replies
    8
    Views
    6,116

    14707 Here you go.

    14707

    Here you go.
  6. Set B1650 to 8170

    Set B1650 to 8170
  7. Not sure whats happening with your pid selection,...

    Not sure whats happening with your pid selection, i have checked here and can select them. Flash this in and select DYNCYLAIR_DMA on the next log as well.12039
  8. Try this and see if any timing is pulled now.12037

    Try this and see if any timing is pulled now.12037
  9. Any Update???? Like everybody else have to tune...

    Any Update???? Like everybody else have to tune and scan a LS1, can read and write with V8 and tune with V7, but unable to scan, simply wont connect.
  10. Replies
    356
    Views
    336,830

    Sticky: Post or PM me your tune file so i can take a...

    Post or PM me your tune file so i can take a look. I'll send it back with something for you to try.
  11. Replies
    17
    Views
    11,449

    Thank you

    Thank you
  12. Replies
    17
    Views
    11,449

    Can someone please email me a copy of this tune...

    Can someone please email me a copy of this tune file as well, Thanks.
  13. Replies
    28
    Views
    20,198

    If it's V2 hook up the power, ground and LED ...

    If it's V2 hook up the power, ground and LED circuits and then use the serial connection, lot more accurate then using AD inputs and no fuss to calibrate.
  14. Replies
    62
    Views
    29,498

    Looks good, looked a bit wierd at first but all...

    Looks good, looked a bit wierd at first but all good now!
  15. Replies
    50
    Views
    75,081

    Sticky: Hi Guys, the only time i've seen this has been on...

    Hi Guys, the only time i've seen this has been on cammed auto E38's that don't have a stall convertor. What i found on the dyno was the VVE cells were being hit from 800 - 2000 rpm and 70 - 105 kpa...
  16. Replies
    11
    Views
    9,978

    Post your tune so we can have a look.

    Post your tune so we can have a look.
  17. Replies
    32
    Views
    32,497

    I agree to a certain point, but I have corrected...

    I agree to a certain point, but I have corrected many tunes from others where their idea of a tune is to slightly modify the VE, MAF and PE to achieve a decent A/F ratio. The end result is MAF and PE...
  18. Replies
    32
    Views
    32,497

    MAFLESS, Tuning with MAF is the lazy way, anybody...

    MAFLESS, Tuning with MAF is the lazy way, anybody can correct a poor VE via MAF. Get your fueling table spot on and throw the MAF in the Bin!
  19. If I was you I would go back to a stock VE Table....

    If I was you I would go back to a stock VE Table. Subtract 40, 30 and 20 percent from the 400, 800, and 1200 rpm rows only. Do this as a starting point. Then follow the auto VE tutorial and dial the...
  20. Try this one. If it is still rich correct your VE...

    Try this one. If it is still rich correct your VE Table values.
  21. Try this and let me know what happens

    Try this and let me know what happens
  22. Replies
    12
    Views
    8,466

    I've disabled TPS VE and made a few other...

    I've disabled TPS VE and made a few other changes. Flash this tune in and see how you go. You need to do an Auto VE with a wideband and correct your Primary VE Table. Once this is done then set up...
  23. Replies
    12
    Views
    8,466

    Something not right there. The come cam will idle...

    Something not right there. The come cam will idle fine at 14.5:1, 950 rpm and 20 degrees timing. It shouldn't be that choppy at idle but have a decent exhaust note. Post your tune file so we can have...
  24. Replies
    12
    Views
    8,466

    Don't disagree with custom O.S's as I use them...

    Don't disagree with custom O.S's as I use them all the time. He just asked for some idle settings. The GTS cal over Custom OS 1 will do fine. No need for a TPS VE table with that cam. Have had 224 /...
  25. Replies
    12
    Views
    8,466

    Tuned a few of these and they produce some...

    Tuned a few of these and they produce some serious cam only rear whel kilowatts. Iv'e almost cracked 300 KW at the tyres. Start off with a GTS mafless base tune. Up the idle to 950, Desired airflow...
Results 1 to 25 of 75
Page 1 of 3 1 2 3