Search:

Listed on ebay:

http://cm.ebay.com/cm/ck/1065-29296-2357-0?uid=125129370&site=0&ver=LCA080805&item=120140205034&lk=URL

Selling because I'm selling my 2003 Silverado. This is a used unit. The...

Listed on ebay :

http://cm.ebay.com/cm/ck/1065-29296-2357-0?uid=125129370&site=0&ver=LCA080805&item=120140206528&lk=URL


This unit was used very little. The LC-1 cable is new or refurbished...

I've only got pin 42 plugged up. Sorry, but i dont understand what hooking up pin 33 does as far as the fans coming on during A/C cycling. Pin 33 just indicates high fan speed right?

So, are you saying to hook up to pin 33 instead of 42? Or is there more involved? I'm looking at {G0106} in the tune and it's set to "fan #2 control" which seems right according to your ls1...

Ok, I corrected the wires and plugged the orange connector to the proper location on V2. Ran a scan and PLX AFR was 10.4min, 13.2avg, and 15.1max

PLX V was 0.2min, 1.6avg, and 2.6 max.

Cells on...

So, if enable is set high, only the engine temp will be causing the fans to come on? Will this not have adverse affects on the A/C system? Isnt there some correlation between the A/C pressure and the...

Great info guys, thanks!

Hmm, wish I had known that about 1 year ago. DOH! :bash:

When the engine temp is below the setting I have for the fans to come on, the fans will cycle on and off at idle. This cycling happens over and over, on - off, on - off. Fans go off for about 5...

It Plugs up just as before, right? I just unplugged (orange connector) it from the V1 and plugged it into the V2.

White wire goes from PLX controller to WB linear output and Gray wire goes from...

Any ideas on what these should be set at (G0911,G0912)?

What exactly does it affect (I know, "If the A/C pressure is above this value, then turn on fan #1)?

What are the effects if the enable...

Have I missed something in the V2 manual for information on this?

I got the V2 hooked, up and after scanning, my Ben_plx2 cells (AutoTune) were way different than the day before when I used the...

yes, everything on the engine block is stock.

LTFT (B3801) and STFT(B4108 ) are disabled. I'm reading values from the PLX WB02. I'm going through the Auto VE tune again because when I returned to closed loop, the stfts were showing -10 during...

Hmm,

So this is an unresolved issue?

Warm idle. Here is a data tab and 2 map tables. First map was done about 4pm, second map was done at 730am. The map file produced yesterday had close to the same cell values for the 400 rpm, 35 and...

I've been logging for quite a while now and the ben maps in the 400rpm row and 35 and 40 kPa columns are consistently lean (1.01to 1.04). THis lean scan is occuring after pasting and multiplying the...

What are the benefits of traction control removal? I would think having this enabled would hinder the ability to have burnouts. I've already searched the forum, found a post where mytinker (sp?) was...

Yes, that makes sense. Question about the "stoich" afr setting in properties. How do I keep the value of 14.7? Everytime i close the tune app, the freakin thing goes back to 14.63 as stoich. Isnt...

It's a PLX, can those be calibrated? I think it automatically recalibrates on startup. Part of the problem may have been that my AFR was set to 14.63 instead of 14.7 Dont know why it was set to this...

No B3605 in Custom OS 3, B3647 table is set per the Custom OS tutorial, 1.00, 1.06, 1.13, and 1.17 . Dont quite understand what you mean by step #2. I dont see 14.7 in the table.

Ok, found the...

Andrew,
This doesnt make sense unless you're referring to cells in the VE table which I'm not hitting. Cells above 2800 rpms arent being hit during the logging (not fond staying that high in RPMs a...

No, my STFTs are averaging -20.8.

so if my B0101 table is returning very accurate LTFTs (-4 to 0), then my STFTs should be closer to the -4 to 0 range, right? Am I missing something here?

{B0101} modifications adjusts the Short term fuel trims? I thought {B0101} was only for Long term fuel trims.