Search:

Type: Posts; User: Tre-Cool; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    1,332

    Sticky: i still use 7.5, 95% of the time too. i've been...

    i still use 7.5, 95% of the time too. i've been slow to go across to v8.

    what would be nice to get in v8 is being able to open hpt's custom os files. i dont care to look at the ve map modification...
  2. Replies
    3
    Views
    338

    report back once u change it.

    report back once u change it.
  3. Replies
    20
    Views
    937

    no worries. im actually going to test that range...

    no worries. im actually going to test that range switch now in my car to see what it does to the tapshift function.

    ok, so i my car if i enable the parameter is makes no difference, but if i...
  4. Replies
    20
    Views
    937

    once i validate a bunch of those settings, i'll...

    once i validate a bunch of those settings, i'll be providing them to the efi guys to implement as standard settings in the software.

    writing the cax file is rather simple'ish but...
  5. Replies
    20
    Views
    937

    u might need to send the tune file to whomever...

    u might need to send the tune file to whomever provided the autocal and get them to set the security link.

    also how is your shifter setup for positions?
    PRNDM ?

    If M is D5, then you may need...
  6. Replies
    20
    Views
    937

    are you using an autocal or v2/v3 unit? 24587...

    are you using an autocal or v2/v3 unit?

    24587

    i dont have any security enabled on the file, but check this version.

    Where did your original trans come from & did you perform a full flash it...
  7. Replies
    3
    Views
    338

    you have used an ecu tune from an e38/t42 aka...

    you have used an ecu tune from an e38/t42 aka 4l60e.

    theres a bunch of parameters that are different between an a4 & a6 in the ecu.

    i.e gear ratios, IMS, NSBU switch etc. (none of these are...
  8. Replies
    20
    Views
    937

    i have changed 1 parameter in this file via a cax...

    i have changed 1 parameter in this file via a cax file the other 2 changed settings were to turn tutd on as if was controlled via bcm.

    test it out.24584
  9. Replies
    20
    Views
    937

    i have a lot more parameters defined for this os...

    i have a lot more parameters defined for this os then efi/hpt has now.

    how is your tapshift activated? via bcm or some other module or is it hardwire like the corvette?

    I have had a sneaking...
  10. Replies
    13
    Views
    5,392

    this is for 7.5, you will need to save into new...

    this is for 7.5, you will need to save into new file and put in the required folder location.
    OS-12617631

    [TU0049]
    ; Description
    ; ...
  11. Replies
    7
    Views
    1,225

    anywhere. thats the v7 format. so if yoru...

    anywhere.

    thats the v7 format. so if yoru using v8 u will need to convert it over to the new format using the conversion tool
  12. Replies
    7
    Views
    1,225

    [BTU0049] ; Description ; ...

    [BTU0049]
    ; Description
    ; --------------------------------------------------------------------------------------------------
    DESC.001 = IVT Weighting Coefficient - AFR Term....
  13. Replies
    7
    Views
    1,225

    sadly, efilive does not have the ivt scaling. but...

    sadly, efilive does not have the ivt scaling. but if you post your os. i can probably find it pretty quick and u can add it to a cax file.
  14. Replies
    7
    Views
    1,225

    the whole point to double stoich/scaling ifr is...

    the whole point to double stoich/scaling ifr is keep as much usable g/cyl as possible.

    there is also a ivt weighting coefficient that needs to be halved to keep the ivt in check.
  15. Replies
    2
    Views
    962

    generally the etc ecu's use GM.APP for...

    generally the etc ecu's use GM.APP for accelerator pedal position
    GM.ETCTP for the actual blade position.
  16. Replies
    6
    Views
    4,470

    Nearly 12 months later, has there been any...

    Nearly 12 months later, has there been any updates on can support ?
  17. Replies
    16
    Views
    1,497

    what else does the gateway module do?

    what else does the gateway module do?
  18. Replies
    7
    Views
    891

    ah ok. so your wired to starter directly then....

    ah ok. so your wired to starter directly then. sounds like a vats issue. sometimes you need to play with the settings to get them going. just turning off vats doesnt always work. you might need to...
  19. Replies
    16
    Views
    1,497

    i would bet that the commodore would be more...

    i would bet that the commodore would be more compatible then the corvette changes since they used a lot of older serial comms gear for the dash clusters. where as commodore gear was all high & low...
  20. Replies
    16
    Views
    1,497

    ok on the corvette os the difference between...

    ok on the corvette os the difference between man/auto is H0162. auto is serial data, man = pulse.

    I know there's a bunch more parameters defined in hpt, which i could easily bring across, but...
  21. Replies
    16
    Views
    1,497

    forgot to ask before what was the corvette os you...

    forgot to ask before what was the corvette os you tried too.
  22. Replies
    16
    Views
    1,497

    what os are you using. i'll see if i can find...

    what os are you using. i'll see if i can find anything if it's not defined already in efilive.
  23. Replies
    7
    Views
    891

    have you got the clutch pedal position sensor...

    have you got the clutch pedal position sensor installed/wired to the ecu or have you tried turning off the clutch check?
  24. its the request os. give it a shot and see what...

    its the request os. give it a shot and see what errors you get. not sure how having a transfer case would make much of a difference.
  25. Replies
    16
    Views
    1,497

    is there a similar os number that has the...

    is there a similar os number that has the required manual option is what i mean. u could then just do a segment swap of the system segment. that seems to be the bit you need to swap.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4