Search:

Type: Posts; User: Prormk163; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    25,218

    Any Chance you can help me out as well? Same...

    Any Chance you can help me out as well? Same Issue
  2. Replies
    94
    Views
    39,877

    Had a wire pull off injector 5, working on the...

    Had a wire pull off injector 5, working on the maf issue. Seems like it's fine while logging, and my iat seems right (5 wire maf)
  3. Replies
    94
    Views
    39,877

    Finally got parts.

    Alrighty well I finally got my Torque converter and new chain. I replaced them and its like a whole new animal, however after starting it up I now get codes po103 and po200. So I have to check my...
  4. Replies
    94
    Views
    39,877

    Well, I programmed the tune into my PCM and it...

    Well, I programmed the tune into my PCM and it ran the same. So I did a compression test while it was hot, with throttle body wide open and each cylinder was between 123-131 PSI. ...Edit.. Which...
  5. Replies
    94
    Views
    39,877

    Thanks, I will try it this afternoon!

    Thanks, I will try it this afternoon!
  6. Replies
    94
    Views
    39,877

    Do my VE numbers look low for a cammed 6.0 with...

    Do my VE numbers look low for a cammed 6.0 with 317 heads? I'm out of ideas and ready to pull the timing cover off to see if my timing chain is loose.
  7. Replies
    94
    Views
    39,877

    Awesome, thanks again for your help. I know that...

    Awesome, thanks again for your help. I know that every forum I've read you have provided guidance and insight so I appreciate all the time you spend doing that.
  8. Replies
    94
    Views
    39,877

    todays log and tune

    2012720128
  9. Replies
    94
    Views
    39,877

    help

    Ok so this may be a stupid question but I don't want to regress, If I use runway highlighting and watch the narrow bands and my wide band and they show lean, I should lower my VE table in that frame...
  10. Replies
    94
    Views
    39,877

    Cl trimming was disabled. I enabled it and hope...

    Cl trimming was disabled. I enabled it and hope to do a log at lunch time. It does idle pretty well after some playing.
  11. Replies
    94
    Views
    39,877

    recent log

    here is a log i did today.
    20125
  12. Replies
    94
    Views
    39,877

    recent tune

    20124

    here is the tune. I do have 317 heads on it as well.
  13. Replies
    94
    Views
    39,877

    http://www.compcams.com/Company/CC/cam-specs/Detai...

    http://www.compcams.com/Company/CC/cam-specs/Details.aspx?csid=1092&sb=2
  14. Replies
    94
    Views
    39,877

    224/230

    224/230
  15. Replies
    94
    Views
    39,877

    Log success

    Alrighty! I was able to do a few logs and some adjustments and its coming along. I am curious however that it seems pretty gutless at the bottom end. I am not sure if thats because of my cam/stall...
  16. Replies
    94
    Views
    39,877

    Sorry, its been a long couple months.

    20101
  17. Replies
    94
    Views
    39,877

    19594

    19594
  18. Replies
    94
    Views
    39,877

    Perfect thanks for looking at it. I did have the...

    Perfect thanks for looking at it. I did have the show units selected but it may not have saved. Thanks again. I'll prob try to do a log tonight!
  19. Replies
    94
    Views
    39,877

    The selected pids are correct for data column and...

    The selected pids are correct for data column and row? And they match the values in main Ve for eq and b5001?
  20. Replies
    94
    Views
    39,877

    calc.vet tune and pids

    195881958919590195911959219593
    So since i have everyones attention, can you guys look at my tune for calc.vet? I have read through the tutorials and i think i have it set up right. believe the...
  21. Replies
    94
    Views
    39,877

    This is good info.

    This is good info.
  22. Replies
    94
    Views
    39,877

    Ya that's not a bad idea. My maf is a 5 wire with...

    Ya that's not a bad idea. My maf is a 5 wire with iat, not sure if cartridges include them. I could get a seperate one.
  23. Replies
    94
    Views
    39,877

    oh gotcha. Thanks for the opinion.

    oh gotcha. Thanks for the opinion.
  24. Replies
    94
    Views
    39,877

    Well, 3" maf (76mm)

    Well, 3" maf (76mm)
  25. Replies
    94
    Views
    39,877

    Is it worth running a maf? I've reas and read and...

    Is it worth running a maf? I've reas and read and it seems nobody has a definitive answer on any definitive pro's. I've noticed a lot of new molars run speed density? Does it aid in tuning precision?...
Results 1 to 25 of 51
Page 1 of 3 1 2 3