That is correct, however this COS5 operating system can be tuned with other software such as HP tuners and LS1 Flash cable for example. The COS5 is only available for 512kb PO1 PCM (as far as I...
Type: Posts; User: Yortt; Keyword(s):
That is correct, however this COS5 operating system can be tuned with other software such as HP tuners and LS1 Flash cable for example. The COS5 is only available for 512kb PO1 PCM (as far as I...
This is only available with Tunerpro ?
I am looking at using N20 on a VZ is there anywhere I can access the custom operating system 04 so I can control the Nos?
Thanks
joecar...Thanks for the response, I am familiar with the PicoScope trace and the position of TDC on the reluctor wheel. I took a guess and set up the reluctor wheel TDC position in the middle of the...
A question about the position relationship of the crank reluctor wheel to the crank position sensor.
When the top dead centre falling edge on the reluctor wheel passes the crank position sensor at...
There is a lot of information on forums using a flex fuel sensor on an LS1, but nothing conclusive on an Australian Commodore. Has anybody successfully used a PO1 or P59 PCM to run a Commodore LS1 on...
GMTECH4 and Joecar got it thank you both, works fine when you look in the correct place.
OK thank you.
Joecar thanks for the prompt response. The version I am using is V7-5-7 build 299 which works fine with an existing 01290005 auto tune however I now need to set up a manual tune.
I have a 2004 lS1 Holden manual 12225074 using 7.5 software and want to upgrade to 01290005 operating system where can I find the operating system to load into the PCM with 7.5.
Found the...
Ok! thanks
joecar
The conversion from a developed HP Tuners operating system to a 1290005 operating system both on 98 and E85 was not straight forward, however was well worth doing with the benefits 1290005...
Was that using the manual transmission shift light settings in the tune (given the turbo 400) or was it being driven by some other means?
20443
Maybe pin 4 instead of 36?
Tried all the settings this did not work either!
Interesting!.....I will try it and report back thanks.
Thanks for the reply I have already set G1206/G1207
Also
B0201
B0202
B0203
B0204
B0205
B0206
B0207
have been addressed.
I am using 01290005 operating system and trying to use the air pump output pin red plug pin 36 to drive a shift light at a programmed RPM.
Activated air pump in the platform and adjusted the setting...
Certainly a reply with a lot of detailed information thank you for the effort and time you put into replying.
I should be able to confidently make the conversion now.
Excellent support light years...
Joe, thanks for the prompt response. I am converting a developed 2bar VCM Suite tune to 1290005 transfering all setting across to EFI Live 1290005 operating system, in particular for the extended...
Can I run 1290005 custom operating system on an LS1 using B3647 and still have the LTFT active by having standard settings in B4205 and having B4108 enabled?
Or does this operating system only...
Joecar and Blacky thank you for the high level of support for this issue, a credit to the EFI Live product.
I now have a better understanding of what is required and if something goes wrong I am...
Thanks for that link, after reading the instructions to upgrade it is obvious that it would be very easy to get into trouble.
I have four questions.
(1) It has been indicated this should be done...
Thank you for the prompt response.
My V2 firmware version is 2.4.65
"edit the config for your PCM (if not already done)," is there a link any where that explains how to do this?
All a little bit confusing this! I am trying to update to the v8 software as it has been indicated this should be done even when using V7 software
I am currently running V7 software 7.5.7 build 211...