Hymey,
Does a DTC need to be set for it to use the B1703 and B1704 tables? Just confused that it mentions in description it’s used when the airflow fault codes set?
Also when setting the...
Type: Posts; User: jmsmotorsport; Keyword(s):
Hymey,
Does a DTC need to be set for it to use the B1703 and B1704 tables? Just confused that it mentions in description it’s used when the airflow fault codes set?
Also when setting the...
What do you mean exactly?
Nothing concrete - managed to make pressure by overfilling trans. But would then clunk into drive and reverse - pulled box back out and checked the 35R drum for cracking - no crack but found what I...
Figured it out. In my re assembly I missed lining the manual valve up with the select switch. It now starts but now there’s no line pressure ��*♂️ I may have dislodged a seal between the pump and...
I have searched high and low but can’t find much information for a complete TECHM replacement procedure.
Does the VIN need to match the PCM? Or is it just a matter of using V8 to Full Flash?
...
I reckon the Yukon is still cable that uses this PCM so should be able to use that OS
Chasing a stock T43 File, OS24239353 - CAL24239647 - Early VE Commodore
So for larger cams we want the EOIT later is this correct? By making the number larger does this also change the SOIT?
Yes it’s not the easiest table to work out what the ms numbers you adjust are actually effecting, the hpt guys have seemed to look into it a fair bit more mainly due to a few extra tables they are...
2175321754
Been doing some more digging and found these calculators to come up with EVC & IVO times. I have based these off a Big Mutha Thumpr camshaft. now my understanding is that I would want...
My understanding is with modifying the injection timing on an aftermarket cam that your aligning the fuel injection time with the opening of the intake valve just before it opens for better fuel...
https://www.hptuners.com/forum/showthread.php?52330-Horrid-Raw-Fuel-Smell-at-idle-Please-Help
https://www.hptuners.com/forum/showthread.php?41350-How-is-injector-timing-calculated
Here are the...
Now I was doing some searching around getting a fuel smell at idle even if it’s actually not rich and I came across a HP Tuners thread that talks about changing injection timing to fix this. Has...
Fixed those out of range tables they didn’t come up when I searched out of range probably because there efi custom tables. Can you give me the Table number for min fueling?
What are the out of range tables?
Wont DFCO control fuel decal when its enabled?
Have fixed the CL OL settings, Missed that one.
Has No 02's plugged in at the moment.
Is that in B3647?
Cheers it’s pretty basic just trying to get it so can start dialing in the VE
2175021751
Plus supporting mods in the valvetrain for cam.
No mods list it’s literally a factory rebuilt spec ls1 with a mutha thumps cam.
Nah mate just factory ones.
am trying to get a rebuilt ls1 running a Mutha Thumpa cam idling and running properly. Will use RAFPN etc but I cant really get it to idle so I can apply it. I know everyone says don't worry about...
VE SS with a VCM532, having an issue that is intermittent. Car generally starts and idles perfect but on occasion when you go to start it it will just crank over give it a blip of throttle it starts,...
Cheers for that. Found a SS one in the depository and it and up as a LQ9. Gored instantly and idle fairly well for a base tune. Added 10% to the VE and actually got a reading on the WB02. Now just to...
Not being real familiar with what the LQ9 came from what would be a good base tune to grab from the file depository. The loom I’m using has no MAF provision any more. It is running straight out of...
Well I must admit I didn’t think it would come to this but here I am, hav rebuilt a LQ9 stoke stroke 9.5:1 Comp, 238/242 114 cam, 90mm TB and edelbrock pro glo intake.
I have the engine on a...