Search:

Type: Posts; User: TunasTwins; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    682

    If you have a wideband. use the weathermanshawn...

    If you have a wideband. use the weathermanshawn method,
  2. Replies
    5
    Views
    1,435

    Just jumping on here and read this. Someone knows...

    Just jumping on here and read this. Someone knows the answer. Good luck cause that seems odd. Quick fix I hope
  3. you need to make sure the PIds are all correct in...

    you need to make sure the PIds are all correct in the map. Its not hitting all the cells because you dont have RPM or map set correctly.
  4. Sticky: yep

    yep
  5. Sticky: Thanks joe. I had a hunch the serial pass through...

    Thanks joe. I had a hunch the serial pass through worked with the original calc pid. i've read up and will look for the cable supplies tomorrow.
  6. Sticky: Im a bit confused about the PID WB settings from...

    Im a bit confused about the PID WB settings from post 476 & 477. Is this assuming I have E0 gas as it divides the equation by 14.7? Without buying a E% test kit, can I use the WB to figure out what...
  7. Sticky: Its here...been waiting years:beer:

    Its here...been waiting years:beer:
  8. Sticky: V2 on its way. Cats next.

    V2 on its way. Cats next.
  9. Sticky: Thanks for the details about the harness. Im at a...

    Thanks for the details about the harness. Im at a crossroads between buying the V2 or upgrading to the tunercats CAN device. Either way, I will have to make the harness for nbo2 simulation. It's a...
  10. Sticky: My work week starts today. I will do the testing...

    My work week starts today. I will do the testing next Wednesday. I got the green light to purchase a V2 but would still like to see this to the end. My next project will be to make a harness to...
  11. Sticky: Im ready now.

    Im ready now.
  12. Sticky: Using the BEN from LTFT for the MAF gives sane...

    Using the BEN from LTFT for the MAF gives sane values. I hooked up my LM-1 again! I am currently messing with the NB simulation output. I have a harness in the car that I ran a couple years ago. The...
  13. Sticky: Should I have the SELBEN in the new calc.pid...

    Should I have the SELBEN in the new calc.pid without the
    *CLC-00-220 factor 0.5 1.5 .4 "iff({CALC.CL}, {CALC.LTFTBEN}, ""{CALC.WO2BEN})""
    CALC.WO2BEN entry? If not, just use the BEN from LTFT...
  14. Sticky: Giving it a shot now. Thanks Joecar! If I go the...

    Giving it a shot now. Thanks Joecar! If I go the Ac pressure route, I'll take the help on setting it up.
  15. Replies
    56
    Views
    12,552

    Will be interested to hear how this works. Its...

    Will be interested to hear how this works. Its hard for me to tell if the calc pids was finalized in the thread?
  16. Sticky: I made the suggested changes Joecar. My "units"...

    I made the suggested changes Joecar. My "units" look off by quite a bit. The VE table values are very low; seeing 55 should be 125. Also, the MAF table has some larger than anticipated adjustments ...
  17. Sticky: That sounds great Joecar. That would seal the...

    That sounds great Joecar. That would seal the deal with my setup. This is on my wifes 05 4.8LTahoe. i'd like to add to the thread for everyone. Ill post a log soon. Even a scan only V1 would be...
  18. Sticky: Thanks Joecar. I dont currently have the setup to...

    Thanks Joecar. I dont currently have the setup to log the wideband to efilive, unless you know a way with my autotap cable. As far as the VE table goes, I am seeing g*k/kpa and the numbers are very...
  19. Sticky: Looking for some help here folks. I had followed...

    Looking for some help here folks. I had followed WeatherManShawn's original tutorial with much success. After an extended break from tuning, I was saddened to read the news of his passing.
    After...
  20. i selected the correct controller. Been away for...

    i selected the correct controller. Been away for a while. I was around when Weatherman Shawn was starting the calc VE tut. I need to get the new laptop going and want to try the latest process. Im...
  21. ATUSB and v7.5 for Windows 7 machine, worked with xp in past

    Just migrating over to a Win7 laptop. Have installed latest version of efilive (7.5.7 build 230) I have the autotap drivers installed. I cant seem to validate PIDs after registering. I have the...
  22. My autotap cable has bidi, its the atusb model.

    My autotap cable has bidi, its the atusb model.
  23. Replies
    201
    Views
    62,480

    great news for everyone

    great news for everyone
  24. Replies
    201
    Views
    62,480

    Thats what I did. It was the first time...

    Thats what I did. It was the first time connecting to this vehicle so I had to validate PIDs but couldnt see dynairtmp. I'll have to try again
  25. Replies
    201
    Views
    62,480

    Well, its there- just not supported??

    Well, its there- just not supported??
Results 1 to 25 of 53
Page 1 of 3 1 2 3