Search:

Type: Posts; User: Camaro SS; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    3,834

    I don't know. I didn't undo all the wire loom, I...

    I don't know. I didn't undo all the wire loom, I just ran a new wire since I didn't have time to really look into it.
  2. Racetronix (SMP) 160 lb/hr low impedance Injectors

    Has anyone ran the Racetronix (SMP) 160 lb/hr low impedance Injectors and got them to idle good with good a/f? If so could you post your tune or let me know what you have the minimum injector pulse...
  3. Replies
    8
    Views
    3,834

    I figured out by checking the resistance between...

    I figured out by checking the resistance between the connector and the pcm pin that the signal wire was bad. After running a new wire the TPS reads zero with the engine running. :mrgreen:
  4. Replies
    8
    Views
    3,834

    Yeah I'm going to check the continuity from the...

    Yeah I'm going to check the continuity from the tps connector to the pcm. I've adjusted the TPS physically and reset the TPS but still acts the same. Researching on LS1tech someone says maybe the...
  5. Replies
    8
    Views
    3,834

    TPS won't reset to 0%

    My TPS will not ready 0% once the engine is running. With key on and the engine not running it will read 0 but once I start the engine it reads around 2-4%. Sometimes it will read around zero and...
  6. Replies
    10
    Views
    8,150

    Paul, I said in post #6 that I had the V2...

    Paul, I said in post #6 that I had the V2 connected to the OBD II connector and my laptop. I am 99.99% sure I have a hardware issue with my V2 and I would like to know what I need to do to be able...
  7. Replies
    10
    Views
    8,150

    Paul, In post #1 I posted what software...

    Paul,

    In post #1 I posted what software version, firmware version, and bootlock version I am running which yes is the latest versions. In post #2 I posted..."If I select F4 Options -> F4 Self...
  8. Replies
    10
    Views
    8,150

    Which pin would I need to check on the OBDII...

    Which pin would I need to check on the OBDII connector to verify there is 12 volts there. I can read and flash just fine through the OBDII connector.
  9. Replies
    10
    Views
    8,150

    I have had the cable connector to the OBDII...

    I have had the cable connector to the OBDII connector and my laptop with a wideband connected and a 0-5V fuel pressure sensor. They had been working just fine but now they don't. For a while I...
  10. Replies
    10
    Views
    8,150

    If I select F4 Options -> F4 Self Tests -> F4 on...

    If I select F4 Options -> F4 Self Tests -> F4 on the V2. The second to last line the numbers only change from 0-1 on all 4 analog inputs, so that means a hardware issue correct?
  11. Replies
    10
    Views
    8,150

    Analog inputs not working

    The analog inputs had been working just fine for a long time and then all of a sudden they quit working. I am running EFILive Tune V7.5.7 (Build 238) and EFILive Scan V7.5.7 (Build 238) Bootlock...
  12. Replies
    4
    Views
    3,710

    What do you mean scan tool programming? You mean...

    What do you mean scan tool programming? You mean through a tech II like the other thought?
  13. Replies
    4
    Views
    3,710

    Tire pressure monitor

    Is there a way to adjust the set point of the tire pressure monitor on a 2010 Chevrolet Pick-Up?
  14. Replies
    10
    Views
    11,759

    Thanks this all helps.

    Thanks this all helps.
  15. Replies
    10
    Views
    11,759

    I am not totally clear on the wiring. I know I...

    I am not totally clear on the wiring. I know I could get the Speartech T56 to 4L80E harness but looking on the Speartech website even if I had a auto engine harness I would still need a 4L60E to...
  16. Replies
    10
    Views
    11,759

    I read those and I didn't see anywhere in those...

    I read those and I didn't see anywhere in those threads if you still need the T56 to 4L80E harness from Speartech to get the 4L80E trans to work with the 4L60E calibration or if you just need to get...
  17. Replies
    10
    Views
    11,759

    T56 to 4L80E setup/tuning

    I am converting my 2000 Camaro from a T56 to a 4L80E and looking for help on how to get it hooked up and tuned the best way. I am using the Custom OS3 based on the 01/02 Camaro OS (12212156). I was...
  18. Replies
    176
    Views
    121,090

    I wish I could view/look at the tune now. So we...

    I wish I could view/look at the tune now. So we probably won't be able to view the tunes until it is publicly released correct?
  19. Replies
    7
    Views
    5,860

    Thanks...I can definitely do all this but I was...

    Thanks...I can definitely do all this but I was getting spark retard during part throttle/light loads. How would the traction control function be reducing spark during part throttle/light loads?
  20. Replies
    7
    Views
    5,860

    Things seem to be much better. I filled in the...

    Things seem to be much better. I filled in the minimum spark advance I wanted to run in B5915 Minimum Spark Advance table and I zeroed out B5901 Catalytic Converter Light-off table. I don't think...
  21. Replies
    7
    Views
    5,860

    Ok thanks, I have tried logging the EST_ pids...

    Ok thanks, I have tried logging the EST_ pids some but it doesn't do it all the time. I will try to log the EST_ pids more. I was hoping someone could maybe look at my tune and a table would pop...
  22. Replies
    7
    Views
    5,860

    Pulling Timing - No idea why

    Sometimes the PCM is pulling timing on my car and I have no idea why. I am running Custom OS3 and I am running my car in OLSD. I have zeroed out all the tables that I can find that add or subtract...
  23. Replies
    8
    Views
    6,023

    I also have issues with radio reception when...

    I also have issues with radio reception when using my RR also. I can put my factory PCM in and my radio reception is much better. I noticed that when I shut the car off once everything drops out...
  24. Replies
    15
    Views
    9,811

    I agree with you on your statement but if I get a...

    I agree with you on your statement but if I get a lean spike to say 16.0 you couldn't even tell it if I didn't have a wideband but sometimes it will go to almost 17.0 and the car stumbes for a spilt...
  25. Replies
    15
    Views
    9,811

    I agree OL is fine. It would be nice to be able...

    I agree OL is fine. It would be nice to be able to run in CLSD and not get the lean spikes when you increase the throttle.
Results 1 to 25 of 52
Page 1 of 3 1 2 3