Search:

Type: Posts; User: jay p; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    2,737

    Thanks for the reply. Jay

    Thanks for the reply.

    Jay
  2. Replies
    2
    Views
    2,737

    2019/2020 E90 scaning

    Any chance you will provide support for scanning on this platform or will it work using existing ECM settings? I have a 2019 Sierra and would be nice to use the stuff I have for something.

    Thanks...
  3. Replies
    2
    Views
    4,365

    I'm not sure if the 2500/3500s are the same, but...

    I'm not sure if the 2500/3500s are the same, but on the 14 and newer 1500s the speed limiter is controlled by the BCM unless it's set to ECM in the ECM tune.

    Jay

    20049
  4. Replies
    85
    Views
    132,059

    This too? www.tunefiledepot.com

    This too?

    www.tunefiledepot.com
  5. Replies
    83
    Views
    153,002

    I did that same my 2010 LMM. I actually had the...

    I did that same my 2010 LMM. I actually had the pressure sensor pipes installed also and didn't turn off any codes. I never had a check engine light in 30k miles (I sold truck in Dec). The edge...
  6. Thread: 2008 lmm

    by jay p
    Replies
    11
    Views
    10,799

    I agree that a single tune is a better solution,...

    I agree that a single tune is a better solution, but you should get a key switch to keep it on the lowest tune if you keep the DSP5 tune.

    Jay
  7. Thread: 2008 lmm

    by jay p
    Replies
    11
    Views
    10,799

    A lift pump would be a good addition. Be careful...

    A lift pump would be a good addition. Be careful when installing the pins in the ECM connector for the DSP switch. There are some good videos showing how to do it I found when I did mine. An exhaust...
  8. Replies
    3
    Views
    4,640

    I have a 2010 A50 tune from my truck. It's not...

    I have a 2010 A50 tune from my truck. It's not the same OS, but will upload it if you want it. I believe the OS is 158xxxx.

    Jay
  9. Replies
    11
    Views
    8,708

    The gas torque converter is different from the...

    The gas torque converter is different from the diesel, so that would add to the cost also.
  10. Replies
    6
    Views
    5,178

    Here are a couple from my 2006 3500. I think the...

    Here are a couple from my 2006 3500. I think the one with the 2011 date is the cold weather flash (one of them is the cold weather flash). I'm not sure these are full flashes since the A40 PCM has...
  11. Replies
    19
    Views
    17,070

    Yes, the temps need to be above/below a temp the...

    Yes, the temps need to be above/below a temp the engine will see.

    example: Min engine temp should be higher than the engine will ever see to keep EGR off ( like 300 deg). and Max engine temp...
  12. Replies
    66
    Views
    33,241

    Is the LMM DSP5 scaling issue and the 2 missing...

    Is the LMM DSP5 scaling issue and the 2 missing tables (B2256 and B2257) going to be fixed in a future release?

    Thanks
  13. Thread: A50 tuning

    by jay p
    Replies
    27
    Views
    17,842

    Any update on the A50 controller?

    Any update on the A50 controller?
  14. Replies
    66
    Views
    33,241

    I also get build 259 for Scan & Tune. The install...

    I also get build 259 for Scan & Tune. The install file says 260, but 259 is installed.
  15. 1744717448 I uninstalled 7.5 and installed...

    1744717448

    I uninstalled 7.5 and installed v211. I still get the same thing. The DSP fuel press is scaled wrong and the base OS is correct.
    Both the DSP5 and base OS calz files were created on...
  16. I see the same thing on LMM DSP5 tunes. Win 7...

    I see the same thing on LMM DSP5 tunes. Win 7 32bit
  17. Thread: adjusting MAF

    by jay p
    Replies
    6
    Views
    4,741

    I had a similar problem with my 2010 except it...

    I had a similar problem with my 2010 except it was at highway speed. I ended up replacing the MAF sensor and the problem is now gone. This happened at about 100,000 miles. They are not cheap, but I...
  18. Replies
    2
    Views
    3,332

    I got it. Thanks Jay

    I got it.

    Thanks
    Jay
  19. Replies
    2
    Views
    3,332

    2010 LMM stock file needed

    Can someone send me a stock unmolested tune for my truck? The truck came with someones poor tune and I like to start with a clean file.

    Thanks
    Jay
  20. Replies
    207
    Views
    225,601

    Sticky: If I'm reading this correctly, I will be able to...

    If I'm reading this correctly, I will be able to flash old tunes with EGR/DPF changes still there but not have the ability to edit them after updating to new versions?
  21. Thread: DSP5 issue

    by jay p
    Replies
    12
    Views
    9,729

    Did you have a DSP5 os installed when you tried...

    Did you have a DSP5 os installed when you tried to read voltages? Without it you won't read any voltage change. I went through the same thing when I installed the switch and someone here told me to...
  22. Replies
    6
    Views
    8,090

    Any reason you recommend the 6128 OS over 6698 &...

    Any reason you recommend the 6128 OS over 6698 & 32483?
  23. Replies
    6
    Views
    8,090

    Look here, you should find what you are looking...

    Look here, you should find what you are looking for.

    http://www.tunefiledepot.com

    Jay
  24. Replies
    5
    Views
    4,431

    I finally got a chance to update the...

    I finally got a chance to update the software/firmware and try the DVT controls. All controls now work as expected.

    Thanks
    Jay
  25. Replies
    5
    Views
    4,431

    I did a clean install of the EFILive software and...

    I did a clean install of the EFILive software and resolved the data logging problem.
    I still have a problem with the DVT controls not working. What should work on an LBZ? I can toggle the check...
Results 1 to 25 of 55
Page 1 of 3 1 2 3