Search:

Type: Posts; User: RC1; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    962

    I've always used ETCPP1 for the pedal and TP for...

    I've always used ETCPP1 for the pedal and TP for actual throttle position and it's always worked as I would expect. It's just that when trying to link the table to the scan tool, the descriptions are...
  2. Thread: Vtapc e92

    by RC1
    Replies
    0
    Views
    380

    Vtapc e92

    Good day,

    In Virtual Torque APC, the APC is linked in g/cyl, but it is tracked in mg/cyl, so it won't actually follow a scan as shown in the attached

    image. Is this something that I can...
  3. Thread: 6L80E T43 Link.ini

    by RC1
    Replies
    0
    Views
    618

    6L80E T43 Link.ini

    Good day,

    Can anyone tell me if there is a Link.ini file for the T43 controller? I'm trying to sort out a couple of things in the T43 calibration.
  4. Replies
    2
    Views
    962

    B8802 Commanded Power

    Good day,

    I'm chasing a couple of throttle closure issues, and I noticed that B8802 Commanded Power has TPS% as the column axis, yet the description says Pedal Position is the column link. In the...
  5. The parameter I'm thinking of is B8311. It...

    The parameter I'm thinking of is B8311. It doesn't kill throttle by description, but limits the torques output in the case where there is a CAN error with the TCM. If your harness has the 16 pin TCM...
  6. Have you pulled the DTC's? Do you know if the CAN...

    Have you pulled the DTC's? Do you know if the CAN bus has a resistor installed in place of the TCM? In the calibration there is a parameter that kills throttle response in the event of a TCM/ECM...
  7. Replies
    9
    Views
    2,091

    It's a little late to update this, but the...

    It's a little late to update this, but the problem was with the fact that I still had an Edge dash hooked to the Canbus when I made these changes. I realized after that having another item on the bus...
  8. Replies
    2
    Views
    963

    After a little more digging I found what I was...

    After a little more digging I found what I was looking for.
  9. Replies
    2
    Views
    963

    Changing Axis Labels

    Is there a way to change the Column Axis Labels in Virtual Torque VTMAP on an E92 controller? It is greyed out and stops at 100kPa and I'd like to extend it out further since this application is...
  10. Replies
    1
    Views
    664

    Right click on your Map, Map Properties, Cells,...

    Right click on your Map, Map Properties, Cells, Empty if Less Than, then enter the value you'd like.
  11. Replies
    9
    Views
    2,091

    Okay officially panicking now. Apparently that...

    Okay officially panicking now. Apparently that didn't fix it, because I went for a drive today and all was good, until I did a Cal Flash for a little change in shift speed and it happened again. It...
  12. Replies
    9
    Views
    2,091

    Hi Carl, LV3 is a 4.3L V6 from 2014-...

    Hi Carl,

    LV3 is a 4.3L V6 from 2014- Silverado, and I'll attach a picture of the Internal Mode Switch, it is attached to the shift selector detent and tells the TCM what position the shifter is...
  13. Replies
    9
    Views
    2,091

    Well it appears as though I found the issue,...

    Well it appears as though I found the issue, although the fix is a little surprising. Because of the original "Range Malfunction" message, I figured I'd look into the IMS (mode switch) to see if...
  14. Replies
    9
    Views
    2,091

    This has been a working combo for the last couple...

    This has been a working combo for the last couple of years, and then all of a sudden yesterday when I went to start a datalog, it gave me this issue.
  15. Replies
    9
    Views
    2,091

    T43 Controller Not Detected

    I have an LV3/6L80E combo that has been working reasonably well up until today, when it all of a sudden says it has a "Transmission Range Malfunction" when trying to access DVT controls for the E92...
  16. Replies
    27
    Views
    11,958

    There is always the option to use one of these, I...

    There is always the option to use one of these, I use one on my Gen V swap and works perfect outputting 14.5V or so.
    ...
  17. Thread: V8 Scan Issues

    by RC1
    Replies
    2
    Views
    931

    Sorry for the late reply, I tried saving the .pld...

    Sorry for the late reply, I tried saving the .pld and saving dash but neither would work. I did find that it worked as long as I was plugged into the ECM, just not unplugged. All appears to be okay...
  18. Thread: V8 Scan Issues

    by RC1
    Replies
    2
    Views
    931

    V8 Scan Issues

    I'm not sure whether it's just me or if there is something strange going on in the software. I'm trying to create a list of Pids for engine and transmission controllers (E92/T43), but I can't get the...
  19. Replies
    2
    Views
    1,163

    Well that was easy! After I posted I decided to...

    Well that was easy! After I posted I decided to see if it had something to do with me failing the MAF while playing with VVE, and sure enough, as soon as I re-enabled MAF the throttle started acting...
  20. Replies
    2
    Views
    1,163

    Throttle position issue

    Good day,

    I'm having an issue with an E92 swap and a lack of throttle movement. This is a '14 Silverado V6, using the original ECM and the Silverado pedal. I've logged what I believe to be all of...
  21. Replies
    1
    Views
    1,876

    Right near the top of that PID list is TCSLIP

    Right near the top of that PID list is TCSLIP
  22. Replies
    6
    Views
    3,280

    Okay this is probably going to sound a little...

    Okay this is probably going to sound a little odd, but I just went back out and tested after updating to V8.3.8, and lo and behold I have an AD1 voltage reading now! Not quite sure what has changed,...
  23. Thread: Injector PW Issue

    by RC1
    Replies
    6
    Views
    2,971

    https://forum.efilive.com/showthread.php?28903-E92...

    https://forum.efilive.com/showthread.php?28903-E92-disable-STFT&highlight=stft
  24. Replies
    6
    Views
    3,280

    I thought the same thing so I did try 2,3,and 4...

    I thought the same thing so I did try 2,3,and 4 and still no go. Oddly, I did not have the Brown wire from the AEM hooked up to the Flashscan, only the white signal, and it works OK on V7.5 that way....
  25. Replies
    6
    Views
    3,280

    I did close it before opening V8.

    I did close it before opening V8.
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4