Thanks Cindy
Type: Posts; User: ecir45; Keyword(s):
Thanks Cindy
Thanks Joecar. Received reply saying graphic designer is out of office for a couple weeks with family issues so have time.
I recently purchased some decals from a guy on eBay and recall in his listing he can do custom stuff. Waiting on a reply back if he can make some with the EFILive logo. Would there be any copyright...
First post in the Calc.VET thread has all the info and links you need. section III. APPENDIX see summary notes to setup pids and maps, other pertinent info is in the summary notes read that whole...
Thanks for the tip. What tune did you use to swap all the timing tables?
Thanks for bringing this up, had the same problem. Looks like we can just zero that whole table out.
Checked I had only ordered one.
You're in Australia right?
I recall Newark Farnell is similar to Mouser and is a international company although it looks like Farnell is now element14.
...
Not sure if this was directed at me, I am only using one wideband. If I recall when I installed mine there was a option for both or one, I chose one.
found image on goggle of inside. The pigtail with the Molex connector is hard wired to the box. The coiled wire (4 conductor) is from an old telephone headset with new ends to match schematic.
...
Cant recall if I bought more than one, pretty sure I ordered more than I needed of the pins though. Will check later when I get home.
spy2520, Thanks for bringing that up.
You want to read through the summary notes, link is in first post of this thread.
http://forum.efilive.com/showthread.php?16280-CALC-VET-Summary-Notes&p=174714&viewfull=1#post174714
I always read 24 or less but didn't think going 25 would make that big a difference :bangin:. As you probably noticed that log was a log of the tune and not setup with Calc_VET pids, I'll get another...
Created a pdf merging post 1 & 8 for this newb to follow.
Sorry forgot spreadsheet in firt post didn't work see post 31
http://forum.efilive.com/showthread.php?4399-VE-Table-Interpolation-SpreadSheet&p=156166&viewfull=1#post156166
Need to remember to do the above on next Calc_VET.
Used the Interpolation SpreadSheet for VE tables then manually smoothed un-hit cells and extrapolate the un-hit cells on MAF tables.
...
Log file is after second Calc_VET. Looks allot better, notice rich on deceleration and at low TPS%. At least its not throwing P0172 Fuel Trim System Rich Bank 1 and P0175 Fuel Trim System Rich Bank 2...
I'll keep that in mind. :bangin:
Only one log right now, the ones I made corrections from. Won't be able to get another till this weekend. Will post one next week for evaluation.
Would there be any benefit from running Calc.MAFT after using Calc.VET or is Calc.VET good enough at getting the VE table right. The only advantage possibly I can see is by using Calc.MAFT you could...
Can now confirm parts list in my earlier post 39
http://forum.efilive.com/showthread.php?23169-LC-2-Digital-Wideband-anyone-try-it-out&p=202535&viewfull=1#post202535
16539
used an old usb...
hopefully this will help when you get to the pdf. Thanks
16509
had CALC.DAT not selected to show in pic above that it makes CALC.VEN invalid.
So CALC.DAT is needed but not shown in pid pic in first post?
First time tuner here. Used calc_pids from first post. All went well except CALC.VEN showed invalid.
More info showed:
Calculated VE, not corrected {CALC.VEN}
Expression:
% =...
NOTE: use the CALC.VE pid units that match your B0101 table, i.e. either % or g*K.kPa....
again I am green here. Look at the calc vet thread part I. 1. A.
http://forum.efilive.com/showthread.php?15236-Calc-VET-correcting-MAF-and-calculating-VE-(in-single-log)
"A. Set Displacement:...