Search:

Type: Posts; User: 26sutphen; Keyword(s):

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    5,202

    i understand, remove password, extract file, xcal...

    i understand, remove password, extract file, xcal converts to efi bin . on most of the 2150 files i tried they identify in the compatability_header as a 2100 and xcal wont convert. Not sure what's...
  2. Replies
    6
    Views
    5,202

    i tried to open files from the current incal and...

    i tried to open files from the current incal and from older 2017 incal and efi didn't recognize any of the files, does anybody know what month and year was used to map out these files?
  3. Replies
    2
    Views
    769

    23856

    23856
  4. Replies
    6
    Views
    1,119

    2384523846

    2384523846
  5. Replies
    9
    Views
    4,370

    Thank you very much

    Thank you very much
  6. Replies
    9
    Views
    4,370

    Ok i should have included that. Old faithful...

    Ok i should have included that.
    Old faithful never online laptop is running 8.2.24 and 7.5.28, v2 has firmware 2.07.140 and boot block 2.07.008
    If i update the v2 to firmware 2.08.175 and boot...
  7. Replies
    9
    Views
    4,370

    Hello, if i update my V2 to the latest firmware...

    Hello, if i update my V2 to the latest firmware and boot block will it still be compatible with the older versions of v8 and 7.5 that i use on my other older laptops? Thank you
  8. Replies
    22
    Views
    7,801

    I will definitely take his advice. I also think...

    I will definitely take his advice. I also think hes from the left coast..... tuning with no smoke and the emissions in place is probably a necessity over there. Thanks again for the help......
  9. Replies
    22
    Views
    7,801

    I will monitor those while im driving. Dom sent...

    I will monitor those while im driving. Dom sent me a base file to try. I don't think i would have gotten it anytime soon. There was quite a few changes made to the file. I was trying one at a time....
  10. Replies
    22
    Views
    7,801

    That is my next step, I was doing one change at a...

    That is my next step, I was doing one change at a time earlier to see if I could make a difference and it didn't work. i can add fuel and timing, the timing i could go easy with but with adding fuel...
  11. Replies
    22
    Views
    7,801

    Thank you for your help , This is actually what...

    Thank you for your help , This is actually what im after. Thats why the burner is still on the truck. The burnout reference was to show that im missing something on the low end limiters. Ill keep...
  12. Replies
    22
    Views
    7,801

    Are either of you guys willing to share a tow...

    Are either of you guys willing to share a tow tune so I can see where I may be going wrong? I still haven't found the trans limiters. I see full throttle torque target . not sure if that interpolates...
  13. Replies
    22
    Views
    7,801

    Yes, either my snap on scanner or oem software...

    Yes, either my snap on scanner or oem software hooked to the backbone.
  14. Replies
    22
    Views
    7,801

    Ok, Kinda what I did. On the pedal map I...

    Ok, Kinda what I did. On the pedal map I requested more torque. Then I went to torque limiters and made sure what I requested was was that or greater. Then I looked at the torque to fuel and made...
  15. Replies
    22
    Views
    7,801

    can you point me to the limiters for the trans?...

    can you point me to the limiters for the trans? and I haven't disabled the traction control. Duh on my part. but the tires don't even slip and activate it. Also when driving and doing a roll on its...
  16. Replies
    22
    Views
    7,801

    I have not, I looked through the parameters but...

    I have not, I looked through the parameters but didn't see anything for torque management.
  17. Replies
    22
    Views
    7,801

    everything is still in place. Thank you for the...

    everything is still in place. Thank you for the prompt reply
  18. Replies
    22
    Views
    7,801

    torque managment

    Hello can someone point me in the right direction for torque management cm2350 ? working with file DO90008.08. The truck runs better with some adjustments but still cant even spin the tires. I'm not...
  19. Thread: 0549 code

    by 26sutphen
    Replies
    5
    Views
    5,460

    I had this, update your v2. this was on a 870 for...

    I had this, update your v2. this was on a 870 for me....
Results 1 to 19 of 19