Search:

Type: Posts; User: MattS; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    1,799

    2007 E38 ECM and OS upgrade?

    Hey all, I have been looking all over and have not been able to find the answer to my question. I have an Edelbrock supercharged, comp camed and LSA ported head L92 from a 2007 Escalade installed in...
  2. Replies
    3
    Views
    2,996

    Update: Found the problem. I talked to Rob at...

    Update: Found the problem. I talked to Rob at #%^&*, he is the one who did the tune, the VATS were already set to disable in the tune. It turns out the pink wire on X2 pin 21 was broken inside the...
  3. Replies
    3
    Views
    2,996

    Thanks for the fast response. The Auto-relearn...

    Thanks for the fast response. The Auto-relearn according to GM, Mitchell Prodemand and my on trial the 30 min will only learn a replacement key it will not relearn the immobilizer prerelease...
  4. Replies
    3
    Views
    2,996

    LMM DSP5 Immobilizer relink problem

    I have an 07 LMM truck in here for a customer, Autocal was purchased from another vender with a preloaded tune for the DSP5 and loss of emissions stuff. Long story short the original ecm was bricked,...
  5. Thread: E67 Timing issue

    by MattS
    Replies
    1
    Views
    2,329

    E67 Timing issue

    I am not sure if this should be in the e67 forum or forced induction. I put i here becuse the E67 supports 2.5 bar with out mods. I am working on a 07 monte carlo turbocharged 5.3 and an auto 4t65e...
  6. Replies
    0
    Views
    2,582

    turbo speed logging

    Ok I am trying to set up my V2 to read/log my Garrett turbo speed sensor. The sensor will output a square wave 5 volt signal at 1/8 the input frequency. The input frequency being one pulse per turbo...
  7. Replies
    19
    Views
    15,280

    The first trike (two up front one wheel in rear)...

    The first trike (two up front one wheel in rear) was a stand alone, but still used the automatic. There was many challanges to get the car to wind up, and then wind up with out limiting the boost....
  8. Replies
    19
    Views
    15,280

    I answered my own question. I had the V2 plugged...

    I answered my own question. I had the V2 plugged in when I started V7.5 but the V8 HAPI was still connected so the vats patch did not show
  9. Replies
    19
    Views
    15,280

    E78 1.4 cruse vats patch?

    Hi all. Does anyone know if there is a vats patch for a 2011 E78 turbo Cruse os 12644082. I have a company who is putting these engines in a trike and is trying to stand alone the engine and...
  10. Replies
    3
    Views
    4,195

    Thanks!! The system still has the ac pressure...

    Thanks!! The system still has the ac pressure sensor, the ac system is charged, who would have thought that with everything there, just missing the ac control panel would send the fans into fail and...
  11. Turbo LS4 odd dma grams/cyl problem with mass air on the dyno

    I have an 07 monte carlo E67 os# 12609256 cal# 12605843 with a LS7x stlye head billet bocked turbocharged set up. The engine rips on open loop speed density, I have the virtual ve tuned spot on to...
  12. Replies
    3
    Views
    4,195

    07 L98 E38 fan problems?

    I am playing with an 07 escalade e38 conversion os 12614088 cal 12614085 in a 69 blazer. I have the system up and running, did the vats mod, the engine fires right up runs and works well except the...
  13. Replies
    2
    Views
    2,908

    Ya, I got the settings, they just don't seem to...

    Ya, I got the settings, they just don't seem to work no matter were I set the upper or lower temp settings. I am working on a monte carlo, kind of a 5.3, not much GM left in the engine. ECU is stock...
  14. Replies
    2
    Views
    2,908

    E67 After Run Fan Settings?

    I have been messing with the after run fan settings trying to get them to run after the car is shut off. This car has an electric water pump, turbo, headers and a lot of under hood heat, so I want...
  15. Thread: LS4 2 bar sensor

    by MattS
    Replies
    2
    Views
    3,186

    I am in the same boat a you, old habbits do die...

    I am in the same boat a you, old habbits do die hard, espically when we have great results.
  16. Thread: LS4 2 bar sensor

    by MattS
    Replies
    2
    Views
    3,186

    LS4 2 bar sensor

    Hi, I have a fiew dumb quesitons. This is the first attempt using efilive for a gas engine. Normally I use efilive for diesel tuning and hptuners for gas (hp is what I started with years ago, old...
Results 1 to 16 of 16