Search:

I figured out what was causing lean numbers in the logs on my car. My fuel pump was failing and has failed. So I'm waiting for the new one and get it installed so I can try to start tuning again.

R.i.p.
He was definately good at simplifing things for everyone to understand, and helped me alot. He will be missed.

I just checked, it looks like in the tuner tool the maf is labled every 125 so I'll change it to that. But it looks like I have to enter each one in the Row Lables.
In the Scan Tool. Is it ok to...

My SELBEN table is logging MAF frequency Hz.

I just did another drive and was able to get some wot logs. I noticed my alternator is not keeping up at idle (which means I'm loosing voltage to...

Fixed and changed to the correct settings.

Correct I do Not have CALC.VEN selected.

I usually get knock at low rpms, mostly idle. But that was the first time I've seen so much. I think it's my coil. So I'm going to swap one off of my WS6 and see if it clears up. Here are a couple of...

Mods: 408 cid iron block, fast 92, 92 tb, ls6 ported+polished heads 2.08/1.60 valves, 11.7:1 compression, cam .248/.254 .622/.614 @114, kooks 1 7/8" stepped to 2" headers w/3.5" collectors,...

Bummer.
On m VET average map I have numbers as high as 2.44 and 2.47, and numerous cells over 2.0 in the upper rpms. Could it really be that lean? I know my wideband has read 17.x a few times at...

I tried to post them larger and had no luck, not sure what I'm doing wrong there. That's why I tried to include the data pages so you could see all the pids being logged.

But I do have a Dyno jet...

Thanks. I hope these work.

http://i297.photobucket.com/albums/mm222/FrozenWS6/98%20TRANS%20AM%202/98TACALCVETSELBEN.png
...

I do have my map set up as you posted g k/kpa. That's why I had to ask, since those numbers seemed off.

I have to ask. Where will I find the how to post maps off of my scan and what program does...

I finally got to get a good log on my 98 after fixing a couple other issues.
Could someone refresh my memory. On my VET average map, is .98 perfect and anything above (higher numbers like 2.27)...

Cool. I like that better because that will keep me close to the tutorial. That way when I refer back to it (and I will) I don't get myself lost. Haha

Or could I just switch those two wires on the orange block and be ok. Move my WB signal wire to #E and my 2 step to #C?

I just went and double checked my wiring. I've got my signal wire going to #C on the 3 wire block. My ground and signal ground going to #D and I've hooked up my 2 step box to #E. Following the...

75 degrees :damnit1:. Colorado is definatly a place I want to visit someday.

My properties page look exactly like that attachment. I've gone off those before. It is definately easier to watch,...

Your data acquisition device, or flash tuner device,
should have a provision in their software to define
the analog input. Enter the following formula:
(Volts * 1.6)+10 = AFR.

I found this in...

Ok corrected it to that. I have to put the car out side in the 25 degree cold today. So I'll use that time out side to run a scan. I'm not sure if or what the ethanol ratings are up here. I think...

Does this look correct. I changed it to this.

*CLC-00-110
factor 0.5 1.5 .4 "{GM.EQIVRATIO} * {EXT.W02DJ1}/14.7"

Sorry for not seeing this sooner. I'm using a Dyno jet Wideband 2 with a gauge in my dash (it is factory programed). I hooked it into the efi live black box with the 3 wire plug. This wideband says...

haha. I have all 3 selected, the front NB's are still there the rear are deleted. It's logging the HO2S11, SELBEN just fine. LTFTBEN shows 1.000 and doesn't change.

So my wideband says lean,...

Thanks again. I was thrown off by the part that said MAF Sensor Calibration.
Mine came up automatically as SELBEN in that location, so I retitled it lol.
Everything matches all the attachments...

Question. I'm making my maps in the scan tool. I made VET (Average). Which is RPM/Map and I added the data filters.
I'm having trouble getting the SELBEN map right. I get MAFFREQ showing in the Row....

http://forum.efilive.com/showthread.php?15552-January-31st-2011-pre-release-(Updated-Feb-03-2011)

The top one listed is for v7.5.149

Ok I still have BEN_lc11 which is w02-analog and W02BEN1 which is BEN from analog wideband 1. So I selected there appropriate supporting pid. No more red x's. So I'll have to hook back up tomarrow...