Search:

Type: Posts; User: Mean Green Z28; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. So far I got advice to remove fuses 52/60/64...

    So far I got advice to remove fuses 52/60/64 under the hood and also remove battery (not concurrently) and connect terminals together for a LONG time to discharge any capacitors in the system that...
  2. Same as in cluster went out or other modules...

    Same as in cluster went out or other modules start acting up but reset once the gauge is disconnected?


    Sent from my iPhone using Tapatalk
  3. AEM X-Series WB took out my Cluster/Aux BCM???

    Not sure where to post this.
    2012 Vagon.
    Bought and installed the AEM X-series WB with the Canbus OBD port option and as soon as it was plugged in, it took out the cluster. Tech2 shows no comm on...
  4. Hey guys, I just haven't had time to do much with...

    Hey guys, I just haven't had time to do much with the amount of rain and general crappy weather we've been having. Here's what I have for now. I returned the IAT multiplier back to stock, and instead...
  5. Just an update, I played around with offsetting...

    Just an update, I played around with offsetting the IAT multiplier table and got a nice idle with no LTFTs, drove around the block and it felt good ... will get tuned and gone over in a week or two
    ...
  6. Scaling Tune after New Injectors ... some Q's

    Hi Guys, been a while! Turbo Silverado Sold and CTS-V Wagon in the Garage now.

    Dabbled with helping tune a bit a few years ago with my Truck, but please consider me a beginner who's eager to learn...
  7. Well now when I put that harness on their page,...

    Well now when I put that harness on their page, it says is discontinued and replaced by the OTHER part number 20822434 ... haha I guess its a gamble now because I can get the new part cheaper from...
  8. Can I use a 2008 engine harness on a 2009 Silverado?

    Lets talk 2008 vs. 2009 Transmission Wiring

    My 2009 Silverado LY5 never had a PRNDL switch as it was internal to the trans., which was a pain in the ass when it came to swapping in a 4L80E ......
  9. can you use something like this to get a speed...

    can you use something like this to get a speed sensor output?
    ...
  10. Isn't the sensor on the tail housing that is...

    Isn't the sensor on the tail housing that is replaced by the transfer case? If so, it should come out of the transfer case. You should be able to replace the cable driven output with a reluctor and...
  11. ISS is used to detect TCC slip (by comparing...

    ISS is used to detect TCC slip (by comparing engine speed to input shaft speed) and slip while gears are engaged (ISS to output shaft with gear ratio). Someone correct me if I'm wrong.

    Sent from...
  12. Well I had another option to buying separate...

    Well I had another option to buying separate guages. Buy just the 5V sending units and use a 5V power conditioner and get 0-5V linear output. I have a DashLogic that can get 0-5V inputs too.
    ...
  13. so I guess we'll have to stick to 0-5volt...

    so I guess we'll have to stick to 0-5volt reference
  14. Logging more than one data stream using Serial Data (Innovate Gauges)?

    Question. I currently log AFR using the serial connection. The gauge I'm using is the Innovate SCG-1 which is a Boost Controller with wideband.

    Can we also simultaneously log Boost/Solenoid...
  15. Ahhhh now I get it Sent from my...

    Ahhhh now I get it

    Sent from my SAMSUNG-SM-G900A using Tapatalk
  16. I thought you had to pick one table (depending on...

    I thought you had to pick one table (depending on the MAP) and only mess with that and not touch the others ... or is this different from the E38?


    Sent from my SAMSUNG-SM-G900A using Tapatalk
  17. Thanks. Will be putting an order in for the...

    Thanks. Will be putting an order in for the Innovate fuel pressure gauge while I'm doing the transmission lines. It, just like the wide band, has serial output so I'm hoping we will able to also...
  18. Well I got a reply from him saying we have to use...

    Well I got a reply from him saying we have to use 408 as there's no 400 on the table. What's the stock psi of these trucks anyway?

    Sent from my SAMSUNG-SM-G900A using Tapatalk
  19. not sure, I've never really checked recently. All...

    not sure, I've never really checked recently. All he had me do was compare the values at 408kPa and add the multiplier and said that's all I need in addition to the other tables
  20. Here's the before and after. Made the changes on...

    Here's the before and after. Made the changes on the Stock tune.

    Basically, we looked at what the injectors flowed in the stock tune at 408kPa (29.653826 lb/hr) .. then looked at how much his...
  21. Yeah I did modify the pid file but didn't get to...

    Yeah I did modify the pid file but didn't get to do much before I had travel for work. Sorry, will get some good runs in when I get back.

    Spoke to Bob at Injector Connection and got a pretty...
  22. I have sent InjectorConnection an email...

    I have sent InjectorConnection an email requesting the IFR table on these 80lb injectors. I know we were having issues with all this at the beginning when we decided to scale the tune. We were...
  23. Hmm wonder if we have to start all over. You...

    Hmm wonder if we have to start all over. You think it's why we're having trouble fine tuning it? And also the wild crazy curves and slopes on VVE table?

    I'll be going back to a smaller 6766...
  24. the pressure you see is from the in tank...

    the pressure you see is from the in tank controller, nothing at the rails .. it's a return-less system.


    Not quite sure of how it all works. We played with settings until we found that we can...
  25. Here ya go. Maybe you can figure out what's been...

    Here ya go. Maybe you can figure out what's been making us scratch our heads for months, haha. The point between normal/PE and lo/hi fuel rates and etc. have been a nightmare to deal with. And...
Results 1 to 25 of 125
Page 1 of 5 1 2 3 4