Search:

Type: Posts; User: Dom_c13b; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. I often run idle rail around 6500-7000 on stock...

    I often run idle rail around 6500-7000 on stock trucks, and up to around 10,000 on big injector trucks.

    I also agree it could certainly be an issue with cross over tubes. Do a fuel return test and...
  2. Thread: CM2250 Marine

    by Dom_c13b
    Replies
    3
    Views
    717

    Ok great. I will get an autocal sent to them so...

    Ok great. I will get an autocal sent to them so they can read the file and send it in. What email address would you like me to forward the file to, or should I just attach it to this post?
    Thanks,...
  3. Thread: CM2250 Marine

    by Dom_c13b
    Replies
    3
    Views
    717

    CM2250 Marine

    Hello,
    Do you guys have any of the CM2250M Calibrations mapped in the editor yet? I've got a remote customer asking for tuning on some Marine 6.7's. I will attach the nameplate data with Cal. ID. ...
  4. Replies
    3
    Views
    891

    Timing is the biggest thing for keeping smoke...

    Timing is the biggest thing for keeping smoke down at idle and cruise.
  5. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    Didn't even notice that! That's pretty...

    Didn't even notice that! That's pretty interesting being that one engine is a 9 liter and one is a 5.9..I know the calibration is different but figured that they would have different os being such a...
  6. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    Did that last file that I posted have the same...

    Did that last file that I posted have the same issues that the previous file did? Just curious if it was a marine thing with the 2mb flash.
  7. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    22660 Here is another QSB read. This is from a...

    22660

    Here is another QSB read. This is from a 355hp 5.9 Marine Engine. I'll paste the OBD read as well below.
    Thanks,
    Dominic

    Description Value Units
    Engine Control Module #1 (ECM1)...
  8. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    Of coarse! That's understandable. Living in Maine...

    Of coarse! That's understandable. Living in Maine we've got a ton of Lobster boats around and the QSL and QSB's are very popular. I should have a read from a QSB 330 over the next week or so. We'll...
  9. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    CM850 2mb Read

    22653

    Above is the read from the ECM in question.
    Thanks for the help.
    Best Regards,
    Dominic
  10. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    What could possibly go wrong.. haha. I will get...

    What could possibly go wrong.. haha. I will get to the engine later this week or early next week. I'll send the file then.
    Thanks,
    Dominic
  11. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    Any update on this? Summer is coming up and would...

    Any update on this? Summer is coming up and would love to be able to flash some Marine Engines. Would be even better if we had editor support!
    Thanks,
    Dominic
  12. Thread: P1223

    by Dom_c13b
    Replies
    3
    Views
    830

    Hi return rate. Bad injectors most likely.

    Hi return rate. Bad injectors most likely.
  13. Replies
    22
    Views
    2,190

    I would certainly take as much advice from Les as...

    I would certainly take as much advice from Les as you can. He's been a huge help to me and many others of this forum. I've never found anything he's said to be anything but 100%. There is a wealth of...
  14. Replies
    22
    Views
    2,190

    Yes, I should have clarified that a bit better.

    Yes, I should have clarified that a bit better.
  15. Replies
    22
    Views
    2,190

    You can adjust the MAF tables to get it to fuel...

    You can adjust the MAF tables to get it to fuel harder down low but as Les said you're emissions systems are not going to be very happy.
  16. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    It is interesting to see how much it's changed....

    It is interesting to see how much it's changed. Not sure what the trace file tells you but this specific ECM is for a QSL9 that's in a Lobster Fishing Boat. It was repowered in 2016 with this engine,...
  17. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    I sure hope it's out sooner than later. I would...

    I sure hope it's out sooner than later. I would much rather use your editor than Calterm.
  18. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    @GMPX do you have an ETA for file editing with...

    @GMPX do you have an ETA for file editing with Efi-Live? I don't plan on tuning the truck until the spring, I just wanted to read the file out and get started before the boat is put up for the winter.
  19. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    I did try with the latest public release but I...

    I did try with the latest public release but I forgot to update my firmware. I'm going to try and read it out again tomorrow with the updated firmware to be sure. I'll send in the read when I get it....
  20. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    So I can get the file to read, but after the...

    So I can get the file to read, but after the ignition time out when I go to save the file I get a pop up that reads
    "Efilive has detected unknown changes in the file that is being opened. Invailid...
  21. Thread: CM850 Support

    by Dom_c13b
    Replies
    29
    Views
    5,844

    Any Update on the CM850s?? I've got one I need to...

    Any Update on the CM850s?? I've got one I need to tune before spring time.
    Thanks,
    Dominic
  22. Replies
    17
    Views
    3,391

    Got it on the dyno with the 488, and first pull...

    Got it on the dyno with the 488, and first pull the trans let go.. Just can't win with this one haha. They have a new trans for it now but the season is over so they are in no rush to get it back...
  23. Replies
    17
    Views
    3,391

    late pistons

    late pistons
  24. Replies
    17
    Views
    3,391

    What kind of Dyno are you using? This dyno is...

    What kind of Dyno are you using? This dyno is notoriously low. It's a big Mustang that always disappoints haha. Example, my personal truck in my sig, I put down 735, then the next weekend went down...
  25. Replies
    17
    Views
    3,391

    They are II 400's, I believe they have body mods...

    They are II 400's, I believe they have body mods but who knows. I've got a FI 488 ETR on the way for it, we'll see what it does with that.
    I have played with timing on the dyno with this truck and...
Results 1 to 25 of 85
Page 1 of 4 1 2 3 4