Search:

Type: Posts; User: Dragbear; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: A50 tuning

    by Dragbear
    Replies
    27
    Views
    6,875

    A50 tuning

    Does this last update in software and filmware allow us to adjust shift points on the A50 TCM?
    I saw there were updates for the A50 but still not sure if will help me with my 2009 LMM

    Thanks for...
  2. Data loging the Edge insight EGT and boost sensors on the V2 ?

    The v2 and the Edge insight use the same data port connection. How hard is it to connect and calibrate the insight sensors to the v2?
    I don't want to complely disable the insight but just tap into...
  3. Thanks it has been driving me nuts!! My next...

    Thanks it has been driving me nuts!!
    My next question is can I get to it or will it be locked with the programing?
    Rick
  4. Lmm question? do they kill the fuel until it sees tire speed?

    It doesn't seem to matter if I am pulling a sled or trying to burn the tires on the street. If I hold the break and floor the gas I get nothing. I can hold it for a long time and get no smoke and...
  5. Replies
    5
    Views
    2,294

    Well I guess that was not the issue. The manual...

    Well I guess that was not the issue. The manual gage reads exactly the same as the boost reading from the data port under the dash. total boost is 35pis.
  6. Replies
    5
    Views
    2,294

    Yes that was exactly right!!!. I installed a...

    Yes that was exactly right!!!.
    I installed a 0-100 pressure sensor for my insight and found the turbo boost was 50psi. That explains the 1800deg exhaust temps. Need to back it back down.
    I guess I...
  7. Replies
    5
    Views
    2,294

    Can't get over 32psi of boost???

    Last year I ran a Mini Max and in the hottest setting the turbo maxed out at 32psi. This was the reading on the Mini Max
    This year I change to EFI Live and it also maxes out at 32psi.
    I just...
  8. Nick what do I get for $450 Rick

    Nick what do I get for $450

    Rick
  9. GMPX you saying you might have a way to tune the...

    GMPX you saying you might have a way to tune the A50s?
  10. I want to tune it so any time I shift into 4low...

    I want to tune it so any time I shift into 4low it will go to 3rd gear start. A lot of the guys have to switch their tcms at the track then switch them back when they are done. It is very rare I use...
  11. I have my first pull Sunday and I will most...

    I have my first pull Sunday and I will most likely just run High range 1st gear until I figure out what to do. I just installed the Fleece 63mm cheata turbo with Danville tuning, egr deleat, transgo,...
  12. What would that include? Do you need mine as a...

    What would that include?
    Do you need mine as a core?

    Rick
  13. Any news on the A50 software???? I don't want to pay $600 to convert to the A40

    I thought there was a beta version floating around. and they were very close to completing the finial version.

    We are close to pulling season and I would like to set up the 3rd gear start

    Any...
  14. I would hate to be with out it!!!! I takes...

    I would hate to be with out it!!!! I takes forever to warm up.

    Thanks
  15. Josh thanks for the information I will give it a...

    Josh thanks for the information I will give it a try
    Does your converter lock? If so about where does it lock?
    Towhaul on or off or does it matter?

    Thanks
  16. That is correct Most of the pullers run this way...

    That is correct
    Most of the pullers run this way now to get away from the defueling on the shift into 3rd.
    I do run 4low manual now.
    I like running 1st gear high range the best. I don't know what...
  17. Ok I found everything Hog I have a few...

    Ok I found everything
    Hog I have a few questions?
    This will only work in 4low, Drive. (Not 4low, m3, towhaul)
    Using Drive I will need to raise 3-4 shift to keep it in 3rd?
    Do you need to lower...
  18. 14708 This is my factory trany tune I looked...

    14708
    This is my factory trany tune
    I looked through it but didn't find the settings I need to change. I will look some more later on but I have to head for work for now.

    Thanks, Rick
  19. Cool!!!!!!!!! How far do you lower 2nd and 3rd?...

    Cool!!!!!!!!!
    How far do you lower 2nd and 3rd? Do you lower MPH or RPM or both?
    I have not looked into the TCM so I am not sure what I will be looking at. I will check it out tomorrow for sure....
  20. Yea I lost it again when I reflashed it. Thanks

    Yea I lost it again when I reflashed it.
    Thanks
  21. Thanks!!! That is what I was hoping to hear. It...

    Thanks!!! That is what I was hoping to hear.
    It is a $600 deal to get the 3rd gear start. You have to buy a new TCM then take to a GM dealer to get it flashed to match your truck then send it away...
  22. i was over on the BBL forum to get some...

    i was over on the BBL forum to get some information on how to do it and saw a thread on making up a new cable to be able to log with the new version of V7 and V8.
    What is this all about?? Do I need...
  23. Thanks for the info Erik I thought I would ask...

    Thanks for the info Erik
    I thought I would ask before I wasted a lot of time with trial and error.
    Now is that with the new update that just came out for the V8?I don't think I have the one...
  24. Is it possible to tune the trany for a 3rd gear start for sled pulling??

    A lot of pullers use this but they buy a 2nd tcm and have it tuned then switch it out at the track.
    Is it possible the tune it with the V2 so you can just flash it at the track when you get there...
  25. Is it possible to log the trany shifts and engine at the same time??

    I am having issues with the engine tuning around the shift points. if I flat foot it from a stop it will miss or skip just before the shift. I can't tell what is going on because I can't see the...
Results 1 to 25 of 28
Page 1 of 2 1 2