Search:

Anyone ? Is the stock pickup an open/closed type circuit ? :nixweiss:

Thanks !
'J

Link fixed :)

"Part Number(s): 57644 Magnetically triggered switch normally open and closed with magnet passage. Same as supplied with Racepack Computer Systems. Fits 3/8" diameter hole in...

Blacky thought somebody here may know.

I have a question about the VSS signal. Does anybody know if a split ring w/ magnet type pickup would work ?...

Thanks for the reply. :)

But, LIVING WITH ? :cry: :x

Hopefully there is an answer to this.

What other PCM do you plan to use ? just another 98 ?

When you say your speed sensor is...

So there is parameters in the pcm for the "to much pressure/hot shift early" ? I do not believe it was too hot, as it was ~50deg out, and I have a big tranny cooler. How to I get rid of that...

I have been having an intermittent problem at WOT at the track lately. The car will fall right on its face 'sometimes' at WOT.

http://j.cz28.com/wotupshift.jpg

Graph here. If you look at it,...

It is REALLY sounding like it's IAT related now. IE: With a blower, your IAT's are climbing, and mine are dropping. We have opposite porblems. Hmmm. I know the MAF will use IAT, but I am in...

Bink: I have no idea. I would figure many others would have had the same problem though ?

Wait4me: I did not see that in the tuning software. I did see a table for timing relating to piston...

OK, thanks. I will give that a shot if the fixed IAT resistor does not change anything. Maybe before sunday I will get a chance, but it is supposed to rain here the next couple of days. Traction is...

Correct, still running in sd mode. Just got back from a ~60 mile trip, and everything ran smoothly. I pretty much followed the tutorial right on. However, my trans is Vac modulated, so the pressure...

Get a wideband. I put it off for too long. Once I got it, and did the auto VE, I was happy right off the bat. Much easier, and much less time consuming. I have not gone back to the MAF yet, but I...

jfpilla :

Currently I have that table at 1.13 (I believe same as what you stated, just different form) all potins above 40deg C and above 70 MAP. Is there a reason for making the whole table that...

SD, actually still on the AutoVE tune. --> The MAF is still physically there, but is positively not plugged in.

'J

Here is a screen shot if it helps.

http://j.cz28.com/1161-at-1174.jpg

'J

Thanks for the reply, again. :)

MAP is between 90-100 during the run. It usually bounces between 92-97. No real difference in MAP between gears.

'J

Thanks for the reply.

I just double checked my file. I have B0701 set at Disable. Maybe there are other places I need to change ?

I did notice this before this weekend. But it was with stock...

Thanks for the reply. I guess I was not clear enough in the question. Given an RPM, say 5600, at WOT it, (the WB) will display a leaner AFR in 1st gear, then be richer in 2nd and more so in 3rd. The...

I just got an LC1 hooked up last week, and did some AutoVe tuning, then went to the track this weekend. I love it, but have a question.

The tune is still an auto VE tune. I cannot seem to get the...

Thanks for the reply. I hooked it up last night, and tested a tad this morning. Everything seems ok thus far. I did hook the white, and blue lc1 wire up to the black wire in the rear 02 harness. Is...

I did some searching, but did not find a definite answer.

Seems to me the easiest logical place for WBO2 heater power/ground would be the factory rear harness that is just laying there...

Thanks Paul.

Paul,

Thanks for the quick and informative response. I am using black box for logging. I will set it to those settings next time out.

'J

While logging at the drag track I have noticed the Fuel trim cell go to 70 or 71 for 1 frame and then back to normal. When it does this the ltrims will go crazy negative (~40%, but just for 1 frame)....

Things going OK ?

98 Owner patiently wating.

'J
jman812@hotmail.com

Thanks for the reply's.

So if I had a 99-02 PCM and harness ? Anyone done this here ?

'J
jman812@hotmail.com