Wondering if this tutorial covers startup
Type: Posts; User: maalmull; Keyword(s):
Wondering if this tutorial covers startup
Hi Joe,
The car runs great making 400/400+ rwhp & Tq on a 6.0, untouched rectangular port heads and a 220/230 117+4 cam on a truck with 32" tire .
Still believe it needs some fine tuning at...
Hi guys,
what tables to correct hanging rpm's on the start up? when I start the vehicle it goes all the way to 2000Rpm's and hangs up there for 2-3 seconds then drops slowly to the desired set...
Thanks
Hi all,
Can you flash a 2000 Ls1 pcm to work on a 03 Sierra?
Thanks,
Found out it’s a ground thanks all.
Thanks guys I will have a look at the TAC connectors, harness & ground circuit
Sent from my iPhone using Tapatalk
thanks for the reply Joe
I will go through these tomorrow.
so u don't think its tuning related?
Hey Guys
I just ported & milled (.025) 317 casting heads on my LS1. The car fired up immediately after the installation then I shut it down. next day I tried to fire it up but the car haven't...
Hi Joe
Thanks for the reply
I will definitely try the sanity test
I have done free air calibration 3 months ago when I installed the wb, never heard about heater calibration though can u...
Joe,
find the attached log & let me know what u think. (its all part throttle)
I want to rule it out is it a Mechanical problem or is it me?
I've heard bad things about LM2 Lately to.
...
I will post it tomorrow since I don't have the log with me at the moment.
By the way what's the difference between CALC.WO2BEN and CALC.BEN1 ?
CALC.BEN1 = {EXT.WO2AFR1}/{GM.AFR}
don't they...
Guys isn't CALC.EQBEN_LS1 same as CALC.WO2BEN since they use the same expression factor = {GM.EQIVRATIO}*{EXT.WO2LAM1} ?
Never got my VE dialed right, also used CalcVet & CalcMaft with no luck...
Guys,
Can someone help me create "Base Efficiency Numerator - External W02LAM1_LS1" ?
I am doing AutoVE based on the latest write up.
Thanks,
Great
Thanks Joe
Hey Guys,
How do you completely disable CL/LTFT/STFT (AutoVE ) I don't want the wideband read stoich .
My goal is to Run Full OLSD without going through COS
is that possible?
Thanks Joe you've been a great help .
I tuned the car but still facing problems:-
1/ first runs , car runs strong (car still on open loop & no mass air involved). On idle I noticed the engine...
Extremely useful
will have to go though these notes very carefully before asking any further questions.
Thanks a bunch!
Running completely from MAF (B0120 set to zero).
I am in doubt that I am doing the AutoMaf the wrong way.
After completing the AutoVE. Do I copy the VE table to the original file and then set...
will go through all the points
I Appreciate ur help.
Sent from my iPhone using Tapatalk
I will go thru your advice and log ETCTP.
Yes the MAF is still there as you know it's a 5pin.
I've a 28 injectors laying around do u recommend installing those and copy the injector tables from...
A/ yes it's DBW
B/ won't go more than 400rwhp
C/yes I am running a serial lm2 wb
D/won't have an access to a dyno until November.
I adjusted the PE TP to 60% and changed PE enable counter to...
I also based my tune on the truck file not using an Fbody HO , LO tables.
Do u suggest 28 injectors ?
Sent from my iPhone using Tapatalk
Thanks Joe
I am running a stock LS1 in a 03 single cab sierra with 317 heads unported milled to .020 and running 215/223 112 cam & stock truck intake with the 25 truck stock injectors.
My TP in...
Thanks