Search:

Type: Posts; User: joecar; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds; generated 18 minute(s) ago.

  1. Thread: No Lockup

    by joecar
    Replies
    8
    Views
    105

    Post tune file.

    Post tune file.
  2. Post pic. Check units are same between logged...

    Post pic.

    Check units are same between logged pid and table columns.
  3. MAP should show barometric pressure (~100 kPa at...

    MAP should show barometric pressure (~100 kPa at sea level).

    Can you log RPM...?

    Check that CKP and CMP sensors are wired correctly.
  4. Thread: Selling my V2

    by joecar
    Replies
    6
    Views
    219

    lol, yes lot's of fun... :)

    lol, yes lot's of fun... :)
  5. Replies
    4
    Views
    172

    So you have the ground from the LNC002 and the...

    So you have the ground from the LNC002 and the ground from the LC-2 connected together and to the middle pin on the FSV1...?

    Are you sure they are both grounds...?

    Disconnect the ground...
  6. Thread: Selling my V2

    by joecar
    Replies
    6
    Views
    219

    Hey Wolfie, it's been fun having you, good luck...

    Hey Wolfie, it's been fun having you, good luck on your new ventures :cheers:
  7. Replies
    4
    Views
    172

    How did you wire up...?

    How did you wire up...?
  8. Replies
    2
    Views
    118

    You can try running a Windows virtual machine.

    You can try running a Windows virtual machine.
  9. Are you running return fuel system (with FPR...

    Are you running return fuel system (with FPR connected to manifold vacuum) or return-less...?
  10. Do you get a MAF DTC...?

    Do you get a MAF DTC...?
  11. C code is from either body/chassis controller or...

    C code is from either body/chassis controller or ABS controller...
  12. How did you wire it up...?

    How did you wire it up...?
  13. Thread: crank relearn??

    by joecar
    Replies
    29
    Views
    18,688

    Some thing is going wrong... when you click CASE...

    Some thing is going wrong... when you click CASE it should pop up telling you to rev engine to 4000+ rpm and to release throttle when engine stumbles...
  14. See post #17 here: need-B9021-for-0125000...

    See post #17 here: need-B9021-for-0125000
  15. I'll take a look...

    I'll take a look...
  16. See the 2 in the Precision field in rcr1978's...

    See the 2 in the Precision field in rcr1978's pics, this is the number of digits after the decimal point.
  17. Thread: GMPP E67 525hp

    by joecar
    Replies
    3
    Views
    96

    Look at GM.ETCTP instead of GM.TP.

    Look at GM.ETCTP instead of GM.TP.
  18. Thread: GMPP E67 525hp

    by joecar
    Replies
    3
    Views
    96

    They take knock seriously...!! They run PE...

    They take knock seriously...!!

    They run PE overly rich, could probably make an extra 10-15 hp by making PE not quite so rich (assuming the IFR and MAF/VE are correct).
  19. Thread: GMPP E67 525hp

    by joecar
    Replies
    3
    Views
    96

    That's the stock GM file that came with the...

    That's the stock GM file that came with the controller for the 525hp crate engine...?
  20. Replies
    13
    Views
    1,089

    Log GM.ETCTP also.

    Log GM.ETCTP also.
  21. Replies
    4
    Views
    137

    Take some logs.

    Take some logs.
  22. Replies
    4
    Views
    137

    How did you do the segment swap (steps...)...? ...

    How did you do the segment swap (steps...)...?

    Which segments did you all swap...?
  23. Replies
    3
    Views
    124

    The later ones might have additional...

    The later ones might have additional functionality (I can't remember off the top of my head).
  24. Sticky: Hmmm, I hate when PhotoBucket does that. Look...

    Hmmm, I hate when PhotoBucket does that.

    Look in the calc_pids.txt file, log all the pids mentioned in there.

    There's a pdf of Calc.VET procedure here somewhere, let me find it.
  25. Replies
    6
    Views
    396

    Log file...

    Log file...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4