Search:

Type: Posts; User: voda1; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    194

    Linkage to spark table

    My B5914 low spark table is using {link: GM.DYNCYLAIR_DMA} but the scaling only goes to 1.00 Where the PID data collected in the log shows max of 4.16???

    How can this be fixed?

    22983

    open...
  2. Replies
    219
    Views
    84,233

    Sticky: Boundry value FYI

    When opening a stock 97C5 tune file in hptuners the boundry value is shown and quite different from later values.
    7.22 boundry and 4.78 normal(B3702)

    22741
  3. Replies
    219
    Views
    84,233

    Sticky: resolution/sampling rate

    By utilizing the 2 external inputs of my V1, or with the converted EGR and A/C inputs. Could monitor camshaft, crankshaft sensors as well #1 spark and #1 injector. Does the scanner support enough...
  4. Replies
    105
    Views
    8,353

    What version of the tuning software are you using...

    What version of the tuning software are you using here?
  5. Sticky: Can't find a CALC.MAFT map. What is the data in...

    Can't find a CALC.MAFT map. What is the data in the Value column above?
  6. Replies
    2
    Views
    442

    question on OL/MAF

    When configuring LS1A for OL/MAF what determines what is controlling commanded fuel, B3605 or B5001?
    B0120=0
    B3801=disabled
    B4205=140c
  7. Replies
    52
    Views
    78,379

    Sticky: Photobucket delete on the maps on first page....

    Photobucket delete on the maps on first page. Need updated.

    pdf was made. see post #48
  8. Replies
    5
    Views
    739

    Is that in all fuel trim cells or only cell #22?

    Is that in all fuel trim cells or only cell #22?
  9. Replies
    1
    Views
    398

    DVT controls and recorder

    The recorder does not seem to pick up any changes made while using the DVT controls. Is that correct or not?
    Using v7.5
  10. Replies
    24
    Views
    4,706

    Why use analog when FlashScan accepts digital...

    Why use analog when FlashScan accepts digital with fewer issues?
  11. Replies
    436
    Views
    73,074

    Could you post up that .map file?

    Could you post up that .map file?
  12. Engine load to mandate when PE is needed or not

    On competitors website forum it was suggested to tune the PE by engine load.

    Settings:
    B3613 MAP enable to 85 kPa
    B3616 Throttle to 10%
    ? ramp in to 1-1.25 (Did not see any ramp-in parameter...
  13. Thread: File synching

    by voda1
    Replies
    9
    Views
    2,536

    File synching

    Looking for an application that automatically synchs files (tune, logs, notes)between my laptop, home desktop, and work desktop. What are you using?
  14. Replies
    219
    Views
    84,233

    Sticky: For early Gen3 the the EOI was 4.77 x 90 = 430...

    For early Gen3 the the EOI was 4.77 x 90 = 430 deg, 70 deg. difference than with the 5.55 figure.
  15. Replies
    219
    Views
    84,233

    Sticky: Links:...

    Links:
    http://www.hptuners.com/forum/showthread.php?32510-Injector-Timing-Reference-Periods-refereencing-what...
  16. Sticky: Followed steps listed above but the FlashScan was...

    Followed steps listed above but the FlashScan was immediately recognized when plugged in. Went to the device manager and installed the Win-2K drivers. Everything is working OK now.

    Thanks
  17. Sticky: I no longer have that version. Is it available...

    I no longer have that version. Is it available somewhere yet?
  18. Sticky: Ok found the 'EFILive Flashscan FSP' device under...

    Ok found the 'EFILive Flashscan FSP' device under the the USB Controllers section of the device manager.

    Trying: Right click --> Properties--> Advanced then check Load VCP (adds a virtual com port...
  19. Sticky: Having same issue after installing v7.5.235...

    Having same issue after installing v7.5.235 software(upgrading from .170).

    When plugging V1 into computer first time the balloon pops saying device install successful. However the device manager...
  20. Replies
    8
    Views
    2,152

    From post#15236(Calc.VET: correcting MAF and...

    From post#15236(Calc.VET: correcting MAF and calculating VE) it shows DYNAIRTMP_DMA as required pid but can be replaced by CALC.B4901.

    CYLAIR_DMA and DYNCYLAIR_DMA are recommended, are there any...
  21. Replies
    137
    Views
    24,179

    Get car on a dyno and work out the timing and...

    Get car on a dyno and work out the timing and fuel settings.

    Or now that you have better understanding of tune and scanner tools you could do what many experienced turners
    have recommended and...
  22. Sticky: Link does not work - shows: vBulletin Message...

    Link does not work - shows:
    vBulletin Message Invalid Attachment specified. If you followed a valid link, please notify the administrator
  23. Replies
    55
    Views
    16,729

    Were the O2's cycling any faster?

    Were the O2's cycling any faster?
  24. On 97 Vette air tube from fuel pressure regulator...

    On 97 Vette air tube from fuel pressure regulator connects to the air bridge between MAF and throttle body. What is it referencing?
  25. Thread: Data Filters

    by voda1
    Replies
    1
    Views
    884

    Data Filters

    I want to copy my data filters to another computer but can't locate them in the file system. Where are they located?
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4