Quick shoutout to Ira. He sent me a new cable, and new ethernet socket for the interface. Cable didn't fix it, but I replaced the ethernet socket, and all is good!!
Thanks again Ira!!
Type: Posts; User: edcmat-l1; Keyword(s):
Quick shoutout to Ira. He sent me a new cable, and new ethernet socket for the interface. Cable didn't fix it, but I replaced the ethernet socket, and all is good!!
Thanks again Ira!!
Talked to Ira. Gonna do an update and try again. I'll let you know in just a few minutes.
Hey Joe, I'm trying to flash from the laptop.
Version 7.5.7 (Build 178)
It's a 411 PCM on the bench. This is the first time in a few months I'm using my EFIlive, and last time it worked fine,...
OK, I have 12v to the interface, because plugged into the ALDL, the screen lights up. This is without it being plugged into the USB. When I have it plugged into the USB, and I disconnect and...
I will be in Germany/Austria from the 6th of July to the 26th. I'm pretty close to booked, but if anyone needs anything, give me a PM or email, and I'll try and fit you in. Germany from the 6th to...
No, but I've been in the market for one. I DO have a Vetronix Mastertech, and probably should get the SPS software at least, even though that probably wouldn't help me right now.
Yep, VINs match. Only difference I can see is the BCC and OS of course.
With the VATs turned off, it has no codes. With it on, it only has a fuel cut off signal not correct code.
03 Vette. Yes, correct VATS won't work. I've used an 03 base file for the new computer.
If I do a compare, they have different BC codes. They obviously have different OS numbers. The car will run...
Tried that.
Problem I'm having is a PCM swap in a Vette. Seems the security doesn't want to work right. I have to set the security to 'none' for it to start. The base file I'm using is a 03...
Any way to REMOVE a COS? Besides flashing over with a stock file. I wanna remove the COS from an existing file.
TIA
See yas there!!!
I don't think he's bringing to the shootout, but he'll be at MIR for the smackdown.
No. Stock sensor, which is 1.5 bar. So, shouldn't we go to about 150 Kpa?
Tuned a SC LS3 today, and the scanner would only read up to 120 Kpa, and we were pretty far past that in actuality. Log attached. Any suggestions?
Thanks.........
5529
Is there no "plug and play" map sensor? I got a ZR1 map, and it's not even close. The connector that is.
TIA
Edit: ZR1 sensor is the same part number as the LS3. Just found out. The sensor they...
Set the G0801 to no. Car runs normal now.
Cured..........
That's good to know. I haven't even pulled his tune. I'm pretty sure his was done by a dealership. He told me the "recall" had been done. I'll post up when I find out. Maybe his wasn't programmed?
I'm not sure. The column lock bypass was done by another shop. We haven't done any work on this one.
TTT
No one has any experience with this?
Does setting the G0801 to NO keep the car from going into limp mode? Mechanical column lock bypass is already done, but customer is getting the "pull key wait 10 seconds" warning, and afterward car...
Nobody??????? Hello??????? Bueller.........Bueller..........
How are you guys logging TC and TF on the Y bodies? All I see for pids are IAC TC and IAC TF. Is this what everyone is using? Custom pids?
TIA
Thanks. Didn't know if there were other fixes that went along with the 8.1 update. Or any other features besides the BBL.