Lower the closed throttle rate a and b.... Had the same issue and fought for a long time. Multiply stock values by like .3. Matter a fact it was roughly the same rpm and tp% too. For some reason it...
Type: Posts; User: camaro10; Keyword(s):
Lower the closed throttle rate a and b.... Had the same issue and fought for a long time. Multiply stock values by like .3. Matter a fact it was roughly the same rpm and tp% too. For some reason it...
Try that tune out and see after you reclock that maf. A factory ls3 uses alot more spark correction for large errors. I think around 26 degrees. I would try it than start sneaking in more timing...
All of the changes listed is correct. I did alot of tweaking on the proportional idle side of things on 2 ls3s I did this spring. If they were tamed too far the surge got worse. That is why I want...
21672
Give this a try and post a log if it helps
The STFTS will go towards zero as the LTFTS are learned. I guess Im confused why your looking at the STFTS with the LTFTS enabled? Not sure where you have the maf placed but Id start by copying...
What are the LTFTs at? Looks like they are enabled, also 02s are not switching, at that rpm Id expect it to switch somewhat. Seems like an awful lot of min idle air although I have not tuned any...
Ok so as far as selecting pids, it's not necessary to select the calculated ones. Such as stft ben or wideband Ben? Because adding the e38 pids under scan and tune doesn't include them. If I don't...
I guess the question I have is I need to use these custom calc pids. In the scan and tune I could not figure out a way to use them being it's under the v7
Indeed I do. But I have it better now. Trying to play with proportional and integral tables. Owner doesnt want to drill a hole and neither do i. Proportional has to be tamed alot and integral has...
Sorry car got put into storage. Here is a log of another Camaro (2013 LS3) Im working on, I would like to use bbl, just got a 16gb sd card, I have dtc definitions loaded. I only really use the v7...
I tried that but it is not supported on my car. I validated pids just to be sure and it did not help
Ballanger Motorsports afr 500. The new remake of the NGK afx. I'll post a log at some time today. Do you want the calc pids I have to for v7?
Been trying to figure out how to configure it using v8 scan and tune. I think I have the e38 pids loaded on now. Only problem is my wb02 and other custom calc pids I use in v7.5 don't show up and I...
Awesome I'll try that, thanks!
Working on my 2010 ss camaro. What do I log to actually see if it's active. Commanded af or lambda never changes its either stoich or pe value. And as far as I know one of the fuel system pids...
No none known but I'm looking into going centri blower.
Is there any pids to monitor this? Seems that people on Camaro 5 using sct or hpt are able to log tank pressure or line pressure by the tank. Otherwise I've considered installing an autometer cobalt...
I had this issue but it was with air per cylinder on a 06 Gto e40. I would check what joecar said as after I renamed the labels like in the example shown it worked for airpercyl. Also validate your...
Ok, no way of knowing without installing a gauge than? Thanks!
I've searched and I cannot find a pid. Cars I'm working on are 2010 Camaro Ss and 06 Gto. Any ideas? Software and firmware are current..
Thanks I'll give it a try!
Unable to find that file too.
Are you sure yours works correct? Mine will just sit on 1.00 g/cyl and go up and down with rpm
Should I just do a file search to find it or do you know what folder is find it in to modify?
Yes when looking at the high octane table. But if you look under configure display units it doesn't have any units listed for it. Does it show up when you highlight the log and look at the tune? It...