Search:

No, I think you got it mixed up. Bosch on the ECM side of the harness and Delphi on the engine side. I need the Delphi ones!

Maybe Bosch makes them also but I don´t think so. Om my connectors it...

Hi,

Right connectors for LBZ wiring harness from engine to ECM.

I need the same ones but for LMM. Left ones shows the engine side. I need the mating connector for making a harness from engine...

Diesel "stinks" woundelful! Ofcause it evaporates, just at a higer temperature compared to petrol. :)

Ok. Thanks! Will have a look at this when I´m back to work.

Hi guys!

Just built me self a bench harness. One question... Does not a lot of DTCs get active because the engine isn´t hooked up to the ECM? Say I load an ECM and send to a customer. What will...

Take a look att this PDF for what release needed. The wiring diagram is in there also. There will be some new PIDs for you to test what position the switch is in.

Anybody know when the calz for...

So, back to the original question. Does anybody know at what engine temp and oil pressure the engine shuts down? If ever? Maybe it just goes into limp mode or reduced power/rpm.

/Joakim

We supplied a twin LBZ installation to the Garmin team in Round Britain Race 2008.
http://www.hunton.co.uk/powerboat-race-2008.html

I have tried 25-30 ft RIBs with single installation with...

I bought mine directly from a Bosch supplier. Bosch no 1 928 498 135 "Matrix 1.2-terminal" for 0.75 mm2 cable. Don´t know what the minimum qty is because I bought 1000 pcs of them at the same time...

I´m trying to find info where the ECU shuts down or goes into limp mode regarding engine temp and oil pressure etc. Does anyone have info about this? LBZ and LMM info needed.

Can you disable this...

I am embarrassed... :) When I had the engine down for the turbo change I forgot to plug the IAT sensor in again. That is what caused my problem.

Now everything is up and running!

Thanks guys!...

Ok, thanks!

I have search the forum and tried everything... still no luck! Can you give me an example of what to do or even better do you have a tune that I can take a look at?

This is what I...

Found this: http://forum.efilive.com/showthread.php?t=5011 where GMPX says that EFILive currently doesn´t support this. This was over 2 years ago. Do EFILive support it now?

I have tried fooling...

Hi everyone!

I have just fited an ATS turbo on my LBZ for some testing. How do I turn off so that the ECM don´t care about the DTC for the vane? Both the solenoid and the position sensor.

Have...

More questions...

I have an engine on its way home. Its an Audi S6 4,2 liter V8. So soon will I start to get this together. :)

What ist the different between the ECMs? The 0411, is that the...

Ok, thanks everyone!

GMPX: I do not agree with you. Fiting sensors is the smallest issue. Cam signal is no problem. Will use the location where the distributer was. Building a wiring harness, no problem. Have build a...

Thanks for your input!

Why not use the E38/E67 ECM? Doesn´t they support COP and VE table for forced induction? 58 crank wheel sounds nice. More Bosch like that would be easier to find for an...

Maybe I should explain more... It´s an Audi 3,6 L V8 from 1990 that I will see if I can get to run with some kind of GM ECM. Why GM? I have EFILive and I can buy the ECM very cheap. Will get away...

As the topic says: What ECM should I choose?

My requirements are:

-Petrol
-V8 (3,6 L if it matters)
-One output per injector
-One output per spark plug
-Able to control turbo wastegate...

I have solwed the problem by taking a potentiometer and adjusted the min and max values by adding resistors on + and - wires. So now we can throttle betwen 0 and 100 %. This setup will be acceptable...

I get what you are saying. :) So there is a limit in this software or in the ECM to do this. Sounds like we must run with another system.

Anyway, this is the errors I get:

09:56:27.765: Request...

Thanks for your answer.

We are not using stock pedal because in the future we will not use a pedal att all. We will use a throttle stick (maybe wrong name) that you have in boats.

Ok, so you...

Hi,

I am a new to this so have patience. :angel_innocent:

We have a "stand alone" Duramax LBZ -06-07 that will be used for marine use and is at the moment hooked up to our dyno. The wiring...