Search:

Type: Posts; User: trona; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    1,071

    This should be my conclusions about getting my CC...

    This should be my conclusions about getting my CC working.
    In the end it turned out to be the TCC control. I foolishly thought that just leaving 12 volt permanently connected to the TCC. and relied...
  2. Replies
    12
    Views
    1,071

    Another Quick question my E38 lt1b does not have...

    Another Quick question my E38 lt1b does not have DTC enable P0054 and P0060
    Are they there and are not seen by the EFIlive tuner?
  3. Replies
    12
    Views
    1,071

    In-Tech you got me excited but when i checked the...

    In-Tech you got me excited but when i checked the enablers and MIL lights they were already set that way.
    One thing though after the codes are cleared the o2s pass the readiness tests but after...
  4. Replies
    12
    Views
    1,071

    Hey There Still having cruise issues. Since...

    Hey There
    Still having cruise issues. Since clearing the failed rear o2 readiness tests allows the CC to lock. I was wondering if I can hook up the rear o2s stick them in the glove compartment
    and...
  5. Replies
    12
    Views
    1,071

    Here is the emisions test failure "Oxygen...

    Here is the emisions test failure
    "Oxygen Sensor Heater X/y Samples Test - B1S2 $0E $12 9.0000 8.0000 Maximum Samples"
    maybe this is a clue
    Thanks
    Dave
  6. Replies
    12
    Views
    1,071

    thanks but already set to 0.00 dave

    thanks but already set to 0.00
    dave
  7. Replies
    12
    Views
    1,071

    cruise control faults

    Here are some more discovery's and problems with my GM C.C.
    I had mentioned that DTCs were disabling my CC. But not just Mill light DTCs but also
    Failing emissions tests. The test that I cant seem...
  8. Replies
    12
    Views
    1,071

    cruise control thoughts

    Hey there
    I just wanted to post some results from my E38 cruise control
    I took me some time to set up the wiring with the clutch switch 12 volts unless depressed, brake 12 volts when depressed for...
  9. Replies
    12
    Views
    1,723

    Just Following up on ZT-2 PID I was successful...

    Just Following up on ZT-2 PID
    I was successful with enabling the WB using a serial WB connection to the V2. The hardware in my case was ZT2 WB controller, Opto Insulator - (protect the V2), gender...
  10. Replies
    1
    Views
    629

    V2 scan procedure

    Hey There
    This is a quick process question.
    I am running the V2 as a scanner. When I start my truck and launch the scan 7.5 the first step is to connect this usually lets me select my controller...
  11. Sticky: Hi there I have been following the instructions...

    Hi there
    I have been following the instructions to preform CALCVET but no where in the instructions does it say how to run the log file to effect changes to the tables I cut and pasted from my tune....
  12. Replies
    12
    Views
    1,723

    Thanks still figuing this out

    Thanks for the file.
    I am new to obd11 scanning and I am still struggling how to identify the WB in the list of PID's
    I keep you posted when I figure it out
    dave
  13. Replies
    12
    Views
    1,723

    I was wondering that myself and in that case...

    I was wondering that myself and in that case would you need to map all the voltages instead of a formula?
    Thanks
    Dave
  14. Replies
    12
    Views
    1,723

    thanks

    Look forward to seeing it
    Thanks
    D
  15. Replies
    12
    Views
    1,723

    Let me try something else. Here is the chart can...

    Let me try something else. Here is the chart can some one help with how to transpose this table in to a PID?
    Voltage 0.15 0.31 0.46 0.62 0.78 0.93 1.09 1.24 1.4 1.56 1.71 1.87 2.02 2.18
    AFR ...
  16. Replies
    12
    Views
    1,723

    Help with ZT-2 Wide Band

    Hey There
    New to EFIlive tuning. My current setup includes a ZT-2 wide band that only has an analog non linear wide band output. My ZT-2 predates the linear ZT-2(rev11).
    Can this signal be mapped...
Results 1 to 16 of 16