I will give that a shot!
Thanks
Type: Posts; User: Big D; Keyword(s):
I will give that a shot!
Thanks
I have enough gray hair and about to be bald at this rate.....
2014 2500HD 6.0, OS of 12657063. Wanted to see how cam position effected power and fuel mpg before really getting into the vve tuning...
Awesome! Thank you for the update.
Paul, thanks for the effort. You rock!
Just for fun, i downloaded the calibration from the vehicle and still giving bad file format. I've been doing some test with cam timing and such and haven't...
Since this has happend, I've updated to the beta software and firmware versions. Unable to open files so I'm going to consider those gone.
Version V7.5.10.323
M10 file is the one that went corrupt. M5 I can still open. The HD stock is the original downloaded file.
After a pc restart, unknown bin file format warning pops up. I can open the stock tune and others just not the last 4 modified files that I have saved. Also tried to compare the latest tune to stock...
Thanks for the info Cindy. Its working fine now that I uploaded the file to my laptop that crashed.
I have created and installed the DSP5 tune which is currently in the ecm/truck. The hard drive failed on my laptop and now when attempting a "read" the $0538 DSP5 Operating Systems cannot be read...
Looks like you found your problem. If there has been a K&N filter in the box the oil could have saturated the element in the meter and cause your issue. the P0101 is a dead give away and will limit...
The wastegate is boost controlled. It uses exhaust pressure and boost psi to open the internal gate to limit boost on stock fueling to around 22 psi. Do a trouble code check with the scan tool and...
Off topic here but Blindawg, if you dont mind me asking where are you located? I can't tell much from your avatar but the terrian looks interesting.
check for a boost leak, there maybe a ripped boot. make sure the waste gate acuator is linkage is connected. use some pliers and try to actuate the wastegate. you should not be able to move it. ...
Any mods? Stock Tune?
Need more data to be logged to get the full story.
log these pids:
CALC.ACTBOOST
GM.FRPACT
SAE.MAF
GM.BARO2
GM.BOOST
SAE.ECT
SAE.RPM
Built trans for sure and it will run real good depending on tuning
Close EFILive and disconnect the interface.
turn key off, plug interface into connector under dash, turn key to "run", plug usb cable into pc, start tune and click read. there maybe errors but just...
Will do Joe. Its going to be at least a week and half before I can get back at it.
Post a log so we can look at what you are looking at.
after you connect and open the PID's such as dmax imp. go to info and validate PID's. This should open more PID's then select whatever you want.
Changed the VIN and sent to ECM using the BiDirection control.
The VIN was the same.
I still had the same results validating the PID's, no go.
Also checked PCM Info and everything matched as...
I will confirm this and report back in a couple hours, thanks for the insight.
What if the VIN is correct, what approach do I take to validate PID's.
I entered VIN, then selected controller and connected to controller. Do I select controller and connect before entering VIN ?
Well the EQIVRATIO was pid worked when not plugged into ECM. :doh2:
When plugged into vehicle EQIVRATIO didnt work. After spending much time, many pids didnt activate even when validating. I am...
Update:
I was able to log eqivratio and it works. So I will setup my ben map to utilize this pid and adjust accordingly. Thanks Joe for the insight, massive help you have been. I will let you all...
Thanks for the info.
I just found my serial cable and will check the adapter tomorrow to make sure its setup as null-modem.
Thanks for the info your process, I will give it a try tomorrow and see...
I needed some help with this guys. I am currently running analog with my LC1. I am going to find my cable tonight to use it as a serial connection. My laptop doesnt have a serial port so I bought a...