Search:

Type: Posts; User: pavetim; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Sc tune

    by pavetim
    Replies
    0
    Views
    825

    Sc tune

    I have a 2017 camaro ss and will be installing a lt4 sc from a zl1 and will run like 8-9 psi boost. My question is you think a stock zl1 tune will be semi close enough to run the car without blowing...
  2. Replies
    0
    Views
    1,325

    AEM wideband integration

    I have an AEM controller and wideband i just got. It has a pigtail with bare wires, how would i attach the proper connector to use on the V2
  3. Replies
    3
    Views
    922

    Dont think so cause my wideband innovate works...

    Dont think so cause my wideband innovate works fine. The only difference between innovate and plx is i need to use a 2.5mm to 3.5mm adapter on the plx. I will play and see if i can get analog to show...
  4. Replies
    12
    Views
    3,899

    Will not l23642et me save pdf but here is...

    Will not l23642et me save pdf but here is screenshot
  5. Replies
    12
    Views
    3,899

    I have PLX SM-AFR with the bosch 4.9. For the...

    I have PLX SM-AFR with the bosch 4.9. For the life of me i cant get it to show in my V2 but my old LC1 shows up just fine. Any tips
  6. I have a 2017 camaro ss. How do you log intake...

    I have a 2017 camaro ss. How do you log intake valve temp? I cant find a pid for that
  7. Replies
    3
    Views
    922

    V2 and PLX wideband?

    Anybody successfully get a PLX wideband to show up using the serial port in efilive. I for the life of me cannot. I have the SM-AFR and it has a Tx port which is a 3.5mm stereo jack serial output. I...
  8. Replies
    9
    Views
    1,694

    Think it was a problem with my wideband. I...

    Think it was a problem with my wideband. I swapped to my old innovate and i get readings, although still do not get a wo2ser eq ratio error data so i do it manully in a spreadsheet. Insee the pid and...
  9. Replies
    2
    Views
    1,905

    Can't past labels

    I am using my V8 to setup some maps. The one i am working on is the MAF table using Hz and the data is EQ error percentage. When I go to the tune and copy with labels then try to past it into the map...
  10. Replies
    9
    Views
    1,694

    Even after copying your data in the foldef i dont...

    Even after copying your data in the foldef i dont see a WO2SER pid
  11. Replies
    0
    Views
    2,833

    Can't get wideband data to show

    I got this to make a pid for equivilance ratio error and added it to the proper folder but i cant get my wideband data to show up on my scanner. What pids do i need to add for this setup, i am using...
  12. Replies
    9
    Views
    1,694

    Ok so i went to the folder you designated above...

    Ok so i went to the folder you designated above and I copied and pasted that whole code box into the file.. I cannot get the WB to show up on the scanner though. I added MAPBARO and W02BEN to the PID...
  13. Replies
    9
    Views
    1,694

    Can you please help as i wanna do some data logs...

    Can you please help as i wanna do some data logs and tune tomorrow
  14. Replies
    9
    Views
    1,694

    This what you need to help me?

    This what you need to help me?
  15. Replies
    9
    Views
    1,694

    Using V8, PLX dm-6 wideband, serial

    Using V8, PLX dm-6 wideband, serial
  16. Replies
    9
    Views
    1,694

    How to make Eq error pid?

    2017 camaro. I didn't see one in the list but i am using a wideband in lamda and trying to tune the maf but how do you get the Eq error pid so i can just copy the data log and then past, multiply the...
  17. Replies
    4
    Views
    1,191

    Thats what i was afraid of that, so Complicated

    Thats what i was afraid of that, so Complicated
  18. Replies
    4
    Views
    1,191

    Nobody know how to log airmass per cylinder or...

    Nobody know how to log airmass per cylinder or why this pid isnt supported?
  19. Replies
    9
    Views
    1,697

    I literally just did my camaro. Trying to figure...

    I literally just did my camaro. Trying to figure out what pids to log so i can look at stuff like fuel, spark, knock, etc.
  20. Replies
    4
    Views
    1,191

    PID not supported?

    Trying to do some logging on my newly tuned 2017 Camaro SS. Well I say tuned but it's just setup for E85 and now I want to get into tweaking it. Most of the tables like spark advance and other go off...
  21. Replies
    1
    Views
    724

    Reset fuel trims on E92?

    I went into passthrough scanner and went into DVT. There is not ecm for e92 to activate. Can i not reset fuel trims in the e92?
  22. Replies
    3
    Views
    885

    I got it stupid me didnt have ecm connector all...

    I got it stupid me didnt have ecm connector all the way. Runs fine now so i will take her out. Need to figure out if i can reset fuel trims. If i go to DVT there is not activate for the e92
  23. Replies
    3
    Views
    885

    Flash errors so frustrating

    I read my stock file from my 2017 canaro ss just fine. Made changes for e85 and now trying to cal flash it. I tried stand alone and it gave me $0281, i tried pass through and it gave me $0101. I...
  24. Thread: Scan setup

    by pavetim
    Replies
    5
    Views
    1,195

    Cool they all works i have some questions though....

    Cool they all works i have some questions though.
    1. The lambda where does it get that info from cause other than when i first started the car it stayed at 1.011 for my whole 50 mile trip to work....
  25. Thread: Scan setup

    by pavetim
    Replies
    5
    Views
    1,195

    Sweet ill give it a shot. I have been outta the...

    Sweet ill give it a shot. I have been outta the gas game awhile i have alot to catch up on. Are there tutorials that work on the E92?
Results 1 to 25 of 319
Page 1 of 13 1 2 3 4