Search:

Type: Posts; User: tinman; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    3,980

    I'll throw in my 2 cents worth as a complete...

    I'll throw in my 2 cents worth as a complete amateur. I found it was hard to get a good quiet tune and deviate much from stock. Overall, the more advanced the pilot is, the more fuel quantity is...
  2. Thread: 2017 Duramax

    by tinman
    Replies
    103
    Views
    134,005

    Tuning issue aside, doesn't this create a...

    Tuning issue aside, doesn't this create a complete monopoly on repair of GM vehicles. You must go to a dealer, pay what ever they want and wait as long as make you?? It's this just the same issue...
  3. Replies
    2
    Views
    2,570

    Thanks. I had it at 1950 so I may bump it a bit....

    Thanks. I had it at 1950 so I may bump it a bit. I'd like to keep the TC happen so I'll probably won't go much higher.
  4. Replies
    2
    Views
    2,570

    Stock 06 duration question

    What's a safe duration to run on a stock DD -no towing, no gauges. Just trying to give my brother a nice clean tune for his truck. Right now I just dropped the third event and left it there. I figure...
  5. Replies
    17
    Views
    11,965

    So basically you're saying don't got down with...

    So basically you're saying don't got down with the angle, only up? This way line pressure won't get too low?

    Any utility in doing the mechanical advance on the TTVA motor. I assume that is that...
  6. Replies
    17
    Views
    11,965

    Adjusting the 2nd gear band helps for a few...

    Adjusting the 2nd gear band helps for a few months but its always goes back to its usual habits . Which direction should I go with the gov. pressure? I've read elsewhere upping the ttva angle a...
  7. Replies
    17
    Views
    11,965

    I still have the shuttle shift and it is driving...

    I still have the shuttle shift and it is driving me crazy . I have tried BW solenoid, GM solenoid, new transducer, and tighten the band about 1/4 turn over. Nothing made any difference. I used efi to...
  8. Replies
    5
    Views
    5,282

    What I was wondering (not having any problems) is...

    What I was wondering (not having any problems) is that it seems to me that going into limp mode is a bad thing. It's there to tell the driver something isn't right and to take action for repair....
  9. Replies
    5
    Views
    5,282

    Trans limp mode ?

    I noticed that in the stock transmission parameters the trans is set to got into limp mode at 235 degrees. But the O/D lock out is set at 270 degrees. Seems to me it ought to go into O/D lock out...
  10. Replies
    207
    Views
    225,503

    Sticky: Funny you should mention Belize. I was just down...

    Funny you should mention Belize. I was just down there.... for reasons mentioned above. A lot of diesel trucks down there, probably all stolen.
  11. Replies
    18
    Views
    11,293

    I have a DTT and shift enhancer. I to have the...

    I have a DTT and shift enhancer. I to have the flare shift as well, always had it. I have adjusted the TTVA with some improvement. But I got to thinking if it would be better to remove the Enhancer...
  12. Thread: timming

    by tinman
    Replies
    28
    Views
    19,434

    Rich can you comment on the theory that increased...

    Rich can you comment on the theory that increased rail pressure at cruising will increase atomization and perhaps a slight increase in timing (higher pressure, more fuel sooner) to help mileage. I am...
  13. Replies
    8
    Views
    8,704

    Rich, I used your excel file to figure the TOPS ...

    Rich, I used your excel file to figure the TOPS I want the tc to unlock at 0 throttle, and that is reflected in the unlock table. I changed the lock table to close the t/h table. I basically want...
  14. Replies
    8
    Views
    8,704

    B4518 12779 b4520 12780

    B4518

    12779

    b4520

    12780
  15. Replies
    4
    Views
    3,374

    I don't have the option to upgrade. Do I need...

    I don't have the option to upgrade. Do I need another OS?
  16. Replies
    4
    Views
    3,374

    PCM Programming error

    Ever since downloading the software with the trans files, I get error 602 - PCM programming error. I uninstalled and re-installed the software and updated the bootloader, etc. I get the code every...
  17. Replies
    8
    Views
    8,704

    I am playing with this and am having problems. I...

    I am playing with this and am having problems. I changed 2nd gear a little and could notice the changes but am at stock now. I would like get 3rd to lock similar to what it is like in T/H but I...
  18. Replies
    30
    Views
    21,029

    What about the pilot? With the larger injectors,...

    What about the pilot? With the larger injectors, more fuel will be injected sooner, so I retarded my pilot timing by 2 degrees and pulled back the mm3 from 15-25% to compensate for my 50hp nozzles....
  19. Replies
    12
    Views
    7,335

    I am running that solenoid also, plus a DTT Shift...

    I am running that solenoid also, plus a DTT Shift Enhancer. I'd be interested in how all this interacts.
  20. Replies
    17
    Views
    9,892

    Thanks for posting your tune. I interesting to...

    Thanks for posting your tune. I interesting to see what others are doing.
  21. Replies
    17
    Views
    9,892

    I'd love to see a single event tune just to see...

    I'd love to see a single event tune just to see what folks are doing. I'm gonna play with that in the future just to see what kinda of mileage I can get. When you drop the pilot, are you combining...
  22. Thread: MM3 vs. PW?

    by tinman
    Replies
    13
    Views
    11,988

    Ahh... Not seeing the forest for the trees....

    Ahh... Not seeing the forest for the trees. Thanks.
  23. Thread: MM3 vs. PW?

    by tinman
    Replies
    13
    Views
    11,988

    Well what am I missing. How does this other...

    Well what am I missing. How does this other programmer make power if all the tables still only go to 140?
  24. Thread: MM3 vs. PW?

    by tinman
    Replies
    13
    Views
    11,988

    So really we should be upping the Duration for...

    So really we should be upping the Duration for more power? I've been looking at another popular programmer and as best I can tell all it does to up the power is increase the commanded fuel on the tps...
  25. Replies
    7
    Views
    8,233

    I'm playing with rail pressure some and...

    I'm playing with rail pressure some and minimizing wear is part of my goal. My thought is to find the minimally effective pressure, keep the curves smooth and nothing more than stock. Right now I...
Results 1 to 25 of 30
Page 1 of 2 1 2