Search:

Type: Posts; User: joecar; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. I found pid("WO2S11") to work ok (it appeared to...

    I found pid("WO2S11") to work ok (it appeared to choose lambda)... I'll have to dig thru my logs.

    You could try pid("WO2S11.EQ_RAT11").
  2. Replies
    4
    Views
    112

    Can you check continuity across the solder...

    Can you check continuity across the solder joints.

    Look at each one thru a magnifer/lupe, see if there are any cracks in the solder joints... you may have to reflow the solder.

    The "wiped"...
  3. Replies
    6
    Views
    169

    KR is short term retard; adaptive spark (sliding...

    KR is short term retard; adaptive spark (sliding from HO to LO) is longer term.


    Hmmm, it is quite odd that ASPARK goes above 100%.
  4. Replies
    14
    Views
    4,502

    Could also do (from V7 scantool): Info->Validate...

    Could also do (from V7 scantool): Info->Validate Pids.
  5. Replies
    1
    Views
    47

    DTC P2125: Take a closer look at the...

    DTC P2125:


    Take a closer look at the connector and the solder connections on the board (wear marks could indicate repeated stress).

    Also check the terminal pins in the connector. Check the...
  6. Replies
    11
    Views
    497

    Post your log file (showing the IGNITION pid). ...

    Post your log file (showing the IGNITION pid).

    Is VATS activating...?
  7. I saw it :)

    I saw it :)
  8. Do you have the user manual pdf...?

    Do you have the user manual pdf...?
  9. Replies
    3
    Views
    113

    If you want to tune your 4L60E shift feel, look...

    If you want to tune your 4L60E shift feel, look at the Torque Reduction tables.
  10. Replies
    2
    Views
    104

    You would have to use a new PCM license on your...

    You would have to use a new PCM license on your new FS... otherwise use your old FS which already has a license linked to your PCM.

    V7 software can read and clear DTC's from other modules, but not...
  11. To clear the Trans Adapts, you should be able to...

    To clear the Trans Adapts, you should be able to do it with key on engine off.

    Hmmm, not sure about Clutch Purge.
  12. Replies
    6
    Views
    137

    Yes, into the file UserCalculatedPids.ini. You...

    Yes, into the file UserCalculatedPids.ini.

    You can read the tune using either V7 or V8 (V8 might be better), you can log with either V7 or V8.

    Tune can be edited only with V7 at present.
  13. Replies
    5
    Views
    181

    Thanks for posting your findings.

    Thanks for posting your findings.
  14. Replies
    18
    Views
    674

    Did Calc.MAFT work ok...?

    Did Calc.MAFT work ok...?
  15. Interesting...

    Interesting...
  16. Sticky: The trans tune would have MAF DTC entries in the...

    The trans tune would have MAF DTC entries in the max line pressure, you can disable those.
  17. Sticky: I believe what was said, I'm just not sure the...

    I believe what was said, I'm just not sure the reason why that table would prevent running MAF at idle.
  18. Replies
    1
    Views
    292

    Thanks (I see there are flex fuel parameters).

    Thanks (I see there are flex fuel parameters).
  19. GM.IBPW1/2 are for LS1 and E40. GM.INJPWB1/2 are...

    GM.IBPW1/2 are for LS1 and E40.
    GM.INJPWB1/2 are for E38, E67, E92.
  20. Replies
    5
    Views
    235

    +1 user manual is outdated. When you connect...

    +1 user manual is outdated.

    When you connect to vehicle, on DVT tab you will see a drop down menu titled "Target Controller", select E38

    then on the Output tab you will see Fuel Pump Duty Cycle.
  21. Replies
    1
    Views
    154

    Log GM.DYNCYLAIR and don't log GM.DYNCYLAIR_DMA.

    Log GM.DYNCYLAIR and don't log GM.DYNCYLAIR_DMA.
  22. Replies
    6
    Views
    238

    It takes time/money to learn, so probably you...

    It takes time/money to learn, so probably you want someone else to do it.
  23. Replies
    1
    Views
    95

    I can't open your bin files using EFILive V7 or...

    I can't open your bin files using EFILive V7 or V8.
  24. Replies
    12
    Views
    726

    Oh, I failed to notice that, thanks.

    Oh, I failed to notice that, thanks.
  25. Replies
    6
    Views
    295

    If the lambda(voltage) equation is correct, I...

    If the lambda(voltage) equation is correct, I would do it like this...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4