Got it, thanks. I just had to do a full flash with the file I've been using. So the process is: full flash of the COS with cax file in place, cal only flash the latest tune file from the original...
Type: Posts; User: tinindian; Keyword(s):
Got it, thanks. I just had to do a full flash with the file I've been using. So the process is: full flash of the COS with cax file in place, cal only flash the latest tune file from the original...
Yes, the file 02020005.cax was in place when I did the full flash of COS5. Then I cal-only flashed my previous tune file from the original OS. B9001 is enabled and I have valid numbers in the lean...
I loaded COS5 the other day and can't get lean cruise to work. The attached cax file (02020005.cax) is in C:\Program Files\EFILive\V7.5\Calibrations and the attached cal_link file is in C:\Program...
Like the title says. In my stock OS ('02 Z28 with M6) the TC drops to 0 when the clutch is pushed in. The weird thing is that it becomes active again if I shift to neutral and let the clutch out....
I haven't looked at those, but they are for the air control (IAC), correct? I was looking for a fuel control trim PID.
In OLSD, with B4108 (STFT Idle) enabled what PID should I log to see what the trims are doing? Would it be SAE.SHRTFT1/2 or are there others specific to idle trim?
That worked, thanks!!!!
I have loaded COS5 successfully but now I want to revert back to the original 12212156 OS. But when I load my last tune file (the one with 12212156) the option to flash PCM and OS is grayed out. I...
It loaded w/o error (Allow cax option checked), thanks again.
Ok, I think I got it. I copied 'cax b.cax' and renamed it to 02020005.cax, then pasted the B9100 section at the end. For some reason my PC didn't want to upload the .cax file so I added the .txt...
Ok, the error message is back. I loaded COS5 and it works fine, 02020005. Then I copied the latest 12212156.cax, renamed it to 02020005.cax and put it here C:\Program Files\EFILive\V7.5\Calibrations....
I loaded my original cax file and do not get the error message.
Works perfect now, thanks guys!!!
Ok. B9100 is back but predictably so is the error message on startup.
Ok, but I can't enable it because I loaded cax b above and B9100 (LC Enable) is gone. LC worked great, before I "upgraded" to build 235.
Ok, that worked (no more error messages), but B9100 is gone - Lean Cruise Enable. So is LC enabled all the time or never? Thanks.
I got the ".cax errors" after upgrading to build 235, OS is 12212156. Error loading B9000, B9003, B9006, B9007, B9011, B9012, and B9100. Only B9100 is actually in the tune, Lean Cruise enable. How...
For my 92mm NW TB - I did some reading and found I had to map Desired Airflow B4307 vs. ECT and also Desired IAC Airflow (IACDES_B) vs. ECT. If the two tables don't match during warmup you need to...
Sorry to bring this up again, but I have the same question about IAC area with a 90 / 92mm TB. What cars / tunes would have a 90mm TB?
Thanks Joe. I'll give it another try with my corrected LC-1 (weather has been crappy here anyway). I understand CALC.W02BEN for AutoVE and I saw in the "tutorial" where I should use CALC.SELBEN for...
Joe,
Yes, these logs are before applying any changes. I didn't apply the updates since the two were so different and I assumed something was screwed up. I have 36# injectors and the tables were...
Hi. My car is a H/C/I M6 '02 Camaro. After I finally got calc.vet to work I made a log to see how far off my VE table was. Then I made another log run for AutoVE. The problem - Calc.VE shows my VE...
I wired the 5-pin connector directly.
My bad. I was looking at C6002, not C6001. One last question. I set the MAF to fail like you advised but when I loaded the tune and started it up the PID SAE.MAF was still changing. I kind of...
Thanks Joe. I feel editing calc pids has more to do with the intricacies of EFILive than actual tuning, but it is what it is I guess.
Ya I had the lambda line in there already. So what PID do I...