Search:

Type: Posts; User: markemac; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,023

    Thanks for looking, I'll look into the load closer

    Thanks for looking, I'll look into the load closer
  2. Thread: Holden Crazy

    by markemac
    Replies
    11
    Views
    4,100

    Holden Crazy

    what happened to holden crazy file site?
  3. Replies
    4
    Views
    1,023

    Anyone have any ideas?

    Anyone have any ideas?
  4. Replies
    4
    Views
    1,023

    E67 early throttle closing 4,000 RPM

    Hi everyone, I have a sand car that came to me to get running, I worked through the VATS issues, and wiring trouble, runs and sounds good, up to 4k rpm. where the throttle closes down and gets super...
  5. Replies
    15
    Views
    3,696

    I have a transplant cadillac in a off road car,...

    I have a transplant cadillac in a off road car, that may be having the same issue, throttle closes down at around 4k nothing i do seems to change it. how was the repair done to the file?
  6. Replies
    135
    Views
    93,838

    Sticky: 2006 Cadillac 4.6L SC transplant into a sand...

    2006 Cadillac 4.6L SC transplant into a sand buggy it needed the relay from pin 56 (start relay) to ignition or could have used a resistor. that was required to get the fuel injectors to have a...
  7. Replies
    0
    Views
    1,157

    LS3 480HP Hot cam LOST WOT ETC

    I am tuning a 2002 corvette with a LS3 480 hot cam replacement engine,
    Problem I lost ETC of 100% somewhere while getting the correct mixture
    After changing, IFR, Engine Displacement
    I first put...
  8. Replies
    6
    Views
    2,585

    E38 trace not working in VVE tables

    I have logging question when running scanning and looking at logs the trace that shows up in the tuning software, on the Na and 2 bar vve, stays all the way on the left (high vacuum area) on the...
  9. Replies
    14
    Views
    8,278

    I have logging question when running scanning...

    I have logging question when running scanning and looking at logs the trace that shows up in the tuning software, on the Na and 2 bar vve it stays all the way on the left (high vacuum area) on the...
  10. Replies
    14
    Views
    8,278

    "]Of course, you could avoid a lot of this if you...

    "]Of course, you could avoid a lot of this if you plan to keep the MAF and just set the high speed air flow setting to just off idle[/COLOR]

    This would disable the VVE and run only with MAF?...
  11. Replies
    14
    Views
    8,278

    It does answer what it should look like, and...

    It does answer what it should look like, and slightly about what generating coefic are, still not clear totaly why it is in there and not just a ve table? what about the diff vve tables how do you...
  12. Replies
    14
    Views
    8,278

    Yes a couple of times and it is great, I didn't...

    Yes a couple of times and it is great, I didn't see those answers in there I'll look again?
  13. Replies
    14
    Views
    8,278

    VVE Which ones

    Ok it worked great, one question about VVE and the differant ones, there are open intake valve closed intake valve.
    the truck has no intake valve
    one bar two bar three bar
    one and two bar make...
  14. Replies
    14
    Views
    8,278

    Thanks, that make sense I'll try it

    Thanks, that make sense I'll try it
  15. Replies
    14
    Views
    8,278

    E38 and Power enrichment

    I have a 2008 5.3L E38 Silverado that was brought into me to tune, it has a homemade turbo install. Stock MAF, Injectors (i am sure they will be too small) the problem I am having is when I get the...
  16. Replies
    9
    Views
    3,532

    Thanks, I did read the trans also. but this comes...

    Thanks, I did read the trans also. but this comes from the license page on efilive.com, as you can see one license does both. but when I try to reflash the engine (e38 is selected automaticaly in the...
  17. Replies
    9
    Views
    3,532

    E38 will not reflash License error

    I need some help with this, I searched the forum for a couple hours, I have not found any answers.:confused:

    I have a 2008 chevrolet truck e-38, that when I started to program it asked me to...
  18. Replies
    1
    Views
    1,355

    E67 Throttle Cable

    Has anyone been succesful runninig a throttle cable with the E67? If so what had to be done in the file? I suspect there will be no idle air control.

    Thanks
    Mark
  19. Replies
    1
    Views
    1,416

    Original Bin File

    I am in need of a factory flash for a 1999 vortech 5.3L truck throttle
    cable. Does any one have one I can have or acces to TIS. I need it for an engine conversion so I do not have a VIN number?
    ...
  20. Thread: AutoVE

    by markemac
    Replies
    17
    Views
    8,567

    Great thanks that is what I thought was...

    Great thanks that is what I thought was happening, I had read that thread last night and missed the part that it fixed the problem thanks for sending me the link,

    Any pointers for dialing the MAF...
  21. Thread: AutoVE

    by markemac
    Replies
    17
    Views
    8,567

    I disabled the codes yet I still got one I think...

    I disabled the codes yet I still got one I think it was P0103,
    when I erased it the car ran very bad does that mean I was forcing it back to MAF with the MAF disconnected? It ran bad with the maf...
  22. Thread: AutoVE

    by markemac
    Replies
    17
    Views
    8,567

    ve sd how tell which is being used

    I have a little question, I ran through the EFI Live Ve tuning Tutorial on this engine swap with a Z06 motor and a 02 camaro pcm, I thought it worked good I go it all set up great, A:F was good on...
Results 1 to 22 of 22