Does the CM2450B controller need all this too? I am not sure what insite is
Type: Posts; User: pavetim; Keyword(s):
Does the CM2450B controller need all this too? I am not sure what insite is
I have a V2 but was looking to get a V3 so I can do some work in my 2022 RV that has a 6.7 cummins ISB. Think it has a CM2450B controller. So the files cannot be read out of them? I need a security...
I have a 2017 camaro ss and will be installing a lt4 sc from a zl1 and will run like 8-9 psi boost. My question is you think a stock zl1 tune will be semi close enough to run the car without blowing...
I have an AEM controller and wideband i just got. It has a pigtail with bare wires, how would i attach the proper connector to use on the V2
Dont think so cause my wideband innovate works fine. The only difference between innovate and plx is i need to use a 2.5mm to 3.5mm adapter on the plx. I will play and see if i can get analog to show...
Will not l23642et me save pdf but here is screenshot
I have PLX SM-AFR with the bosch 4.9. For the life of me i cant get it to show in my V2 but my old LC1 shows up just fine. Any tips
I have a 2017 camaro ss. How do you log intake valve temp? I cant find a pid for that
Anybody successfully get a PLX wideband to show up using the serial port in efilive. I for the life of me cannot. I have the SM-AFR and it has a Tx port which is a 3.5mm stereo jack serial output. I...
Think it was a problem with my wideband. I swapped to my old innovate and i get readings, although still do not get a wo2ser eq ratio error data so i do it manully in a spreadsheet. Insee the pid and...
I am using my V8 to setup some maps. The one i am working on is the MAF table using Hz and the data is EQ error percentage. When I go to the tune and copy with labels then try to past it into the map...
Even after copying your data in the foldef i dont see a WO2SER pid
I got this to make a pid for equivilance ratio error and added it to the proper folder but i cant get my wideband data to show up on my scanner. What pids do i need to add for this setup, i am using...
Ok so i went to the folder you designated above and I copied and pasted that whole code box into the file.. I cannot get the WB to show up on the scanner though. I added MAPBARO and W02BEN to the PID...
Can you please help as i wanna do some data logs and tune tomorrow
This what you need to help me?
Using V8, PLX dm-6 wideband, serial
2017 camaro. I didn't see one in the list but i am using a wideband in lamda and trying to tune the maf but how do you get the Eq error pid so i can just copy the data log and then past, multiply the...
Thats what i was afraid of that, so Complicated
Nobody know how to log airmass per cylinder or why this pid isnt supported?
I literally just did my camaro. Trying to figure out what pids to log so i can look at stuff like fuel, spark, knock, etc.
Trying to do some logging on my newly tuned 2017 Camaro SS. Well I say tuned but it's just setup for E85 and now I want to get into tweaking it. Most of the tables like spark advance and other go off...
I went into passthrough scanner and went into DVT. There is not ecm for e92 to activate. Can i not reset fuel trims in the e92?
I got it stupid me didnt have ecm connector all the way. Runs fine now so i will take her out. Need to figure out if i can reset fuel trims. If i go to DVT there is not activate for the e92
I read my stock file from my 2017 canaro ss just fine. Made changes for e85 and now trying to cal flash it. I tried stand alone and it gave me $0281, i tried pass through and it gave me $0101. I...