Search:

Type: Posts; User: moatsman5000; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    246

    I think I answered my own question, these are 2.5...

    I think I answered my own question, these are 2.5 ohms so I would need an injector driver or do some resistors in series. AM I correct we need high impedance for the LS1 ECU's?
  2. Replies
    1
    Views
    246

    Will these injectors work?

    Are Peak and hold the proper type of injectors for a LS1 setup? I can get a great deal on a set of 4 of these RC Pl4-1000's, they have the Bosch style top so I think they will work....
  3. Thanks for the feedback. This was my very first...

    Thanks for the feedback. This was my very first run and I assumed I needed to get a higher cell hit count to be more accurate. This was derived forma 45 min drive my lowest hits were around 30 and...
  4. got my wide band 02 installed and went through...

    got my wide band 02 installed and went through the autove process today. Need to spend more time hitting the cells and playing around but I think I have the basics down.
    Stock 5.3 VE
    23012
    My...
  5. I tried to do a segment swap today with no...

    I tried to do a segment swap today with no success. Just to recap I have a 5.3 LM7 stock engine with a complete 2001 Trans am F body intake, injectors, knock sensors, MAF etc. I have this mated to...
  6. Joecar, I deleted the rear O2 sensors and left...

    Joecar, I deleted the rear O2 sensors and left the front o2's wired as they were. I had so many parts from different cars I don't know what o2's went back in. I did replace one of the o2 connectors...
  7. Idle Air control and 02 Heater performance

    I have just finished a LS Swap into a 2000 BMW 323C1. It is a 2005 LM7 with a 2002 LS! computer intake and accessories. It is a manual. I removed all of the emissions stuff, set the Cylinder...
  8. Replies
    24
    Views
    1,926

    Any good tuning write ups with MAF? The...

    Any good tuning write ups with MAF? The autotuneve seems to be for SD. Am I mistaken?
  9. Replies
    24
    Views
    1,926

    Doc, I am running the injectors from the...

    Doc, I am running the injectors from the original 2002 Camaro (Part number 280155931 / 12561462) rated at 24.8 lb per hour @ 3Bar and 28.2 @ 4Bar based on the link below. I am running a Corvette...
  10. Replies
    24
    Views
    1,926

    Yep I love the re engineering aspect of a "motor...

    Yep I love the re engineering aspect of a "motor swap" project. I think I have the AC figured out. I bought an adapter that mounted the E46 Compressor to the 5.3 and retained the whole E46 physical...
  11. Replies
    24
    Views
    1,926

    Thanks for the feedback, I went ahead and flashed...

    Thanks for the feedback, I went ahead and flashed the manual tune I referenced above and it still starts, idles and revs OK. Once I get my driveshaft adapter from Collins engineering I can start...
  12. Replies
    24
    Views
    1,926

    And some photos because everyone likes pictures...

    And some photos because everyone likes pictures :)

    https://lh3.googleusercontent.com/Aag1Fhaz_RGcGqPDFshtLyVbqA69xTsJRTcTAaEq0t-XUb9hI-vBVLZ19loxKqt7upMMAuK3GlXC5F55ULQFXf2WX8oSVx_IH1m8 ...
  13. Replies
    24
    Views
    1,926

    Yep its a stock 5.3 motor other than the LS1...

    Yep its a stock 5.3 motor other than the LS1 intake and custom short tube to 2.5 inch exhaust I built for it. It seems to idle and rev great under no load. I want to ditch the MAF and go SD, will...
  14. Replies
    24
    Views
    1,926

    I have posted my tune file with VATS removed and...

    I have posted my tune file with VATS removed and a tune file I found for a manual via a dropbox link from this forum somewhere. I was trying decide the easiest way to convert from automatic to...
  15. Replies
    24
    Views
    1,926

    Thanks for the welcome, Joecar. I wrote a really...

    Thanks for the welcome, Joecar. I wrote a really long post with all of my information, links and pictures however I received a message that a moderator would need to approve it for some reason. ...
  16. Replies
    24
    Views
    1,926

    LS1 ECU on 5.3 setup

    Hey everyone, I am new here and getting ready to start tuning my first ECU. I have been doing a ton of reading and so far I was able to remove the VATS and get the motor started. It idles but I don
  17. Replies
    6
    Views
    2,242

    Thanks!! It is working as expected now. Just...

    Thanks!! It is working as expected now. Just flashed my first PCM. Removed VATS now I have a ton of reading to do to start tuning. Thanks again for supporting such an old platform and getting my...
  18. Replies
    6
    Views
    2,242

    I am still unable to flash a PCM after putting...

    I am still unable to flash a PCM after putting the new licencing in. See the screenshots below. Help->FlashScan V1 PCM licensing still shows "Personal Scan&Tune" and only 2 PCM licences. If you...
  19. Replies
    6
    Views
    2,242

    Thanks Blacky!! I just installed it however I am...

    Thanks Blacky!! I just installed it however I am at work and will test a flash once I get home. How many PCM's will I be limited to? Also can you help me fix my account I accidentally used my...
  20. Replies
    6
    Views
    2,242

    Unable to register flashscan v 1.2

    I am attempting to use a Flashscan v 1.2 unit I bought second hand. When trying to flash a PCM I am receiving the error “The attached device is a Scan Only device” I believe I have followed the...
Results 1 to 20 of 20