Search:

21096 I was checking to see if I'm Logging the correct PIDs for Injector Duty Cycle Correctly. Its getting up to 237%. Also my Map is running about 80kpa cruising at 75mph. 2010 Silverado 6.2...

nevermind I made a new serial cable

I need a little help getting my LM-1 set up for analog. I have Red,white and a bare wire on the analog cable. What wires do I put i the V2 A/D inputs and then what to I have to do to set up the V2...

Thanks that worked great. Could you tell me what you had to do to correct the problem.

I have 2009 silverado 2500 6.0l 6l80e trans OS 12630501. It had mechanical fan on it and we installed a factory efan setup on it because of the body lift on it.
We have the pins in the correct...

I just adjusted the t/body closed now im about 20 steps on the IAC motor. I seemed to help a little,but about at 1400 rpm it stays and goes down to the 875rpm. The Maff at idle is 20g/s.

I got a friends 02 camaro with a 408 with a 96mm t/body. Im in the process to do the Calc.VE tune. When I snap the throttle it IAC opens then Its slowly goes down? Im not sure where to change it...

I was want to try to play with CALC. VE Table. Where in efi live do you go to make the pids and how do you make.

I have a pcm out of a 04 silverado. I have a ls1 that i need to convert it to a LS1 OS. what do i have to do to be able to flash it to it.

do i use the BEN factor serial wideband E38 style for the E38 and E67

also what do I need to change and thing else. like changing the outputs in the lm 1. Im not sure. Im new a using the WBO2

What PIDS do I need to log a vve on the E38 and E67 ecms. I using a LM1 with serail cable. I just want to make sure i use the correct pids when i logg a file.
What BEN do i need and all all the...

I wanting to install efans on a 2000 silverado, with OS 09381344. I was wanting to know what pcm pin to install the relay ground and has anyone had any issues with this install. I looking at...

I got a 2000 vette that i installed a 237/242 .603/.609 112lsa. Im trying to do the auto ve. can get the car to idle right. I need a little help to maybe get to the ve where the car will idle. look...

lq4 short block, stock ls2 cam.arf 225 heads. stock injectors

joe car thats what i have selected. I know when i do the Auto VE and put it back to closed loop .the ltft or very lean. but the auto ve is +-.01.I did post a screen shot of my PID list.

here is the pid list. i though it loaded last time

here is a copy of my PID list. look it over and see if its right.I just slected the
WO2EQR1

joecar i was not logging WO2EQR1. but what ben map to have to edit. I been logging
BEN factor bank 1,serail wideband ls1 factor. do i need to to edit it. if so have to i do it. thanks

do you have to adjust the anolog 1 or 2 voltages

yes the free air has been calibrated
i just looked at it its set up for gas

I have LM 1 set up to run on serial cable.I think im geting inaccurate test results when im logging my VE.I did set my V2 to the tutorial by TAQuickness. Do have to set up the lm1 with the software...

I have been doing my auto VE with the LM 1 with the serial cable.I got the ben factor in +/- .01).useing the filters. The ltft goes up to 20% when i put it back in closed loop.I have the maf disabled...

do i reenable the c2901 and c2903

I have beening reading up on tuneing the maf in the tut.I have my auto ve completed. So what do i need to do to calibrate the maf. I have a LM-1 that im using. Do i enable the stft and ltft. or...