Search:

Type: Posts; User: azzhauler; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    3,965

    V1 doesn't want to connect to scan

    I know this cable is an oldie, but here goes. I have a v1 that I used for my ls1 car, and my other car recently popped an engine light so I was trying to connect on the scan tool to see what's going...
  2. Replies
    1
    Views
    1,692

    Validating PIDs

    When validating PIDs, what determines which ones are available? I'm having an issue with an 12200411 pcm that I have swaped into my 98 Sierra using the calibration/os from a 01 Express van, as quite...
  3. Replies
    1
    Views
    2,092

    Wondering about a table

    I've been messing with my tune a bit recently and stumbled upon table B5908 Fuel Mixture Spark Correction. I was just wondering why this table even exists? Seems to me it couldn't do a whole lot that...
  4. Replies
    1
    Views
    1,847

    Does this afr reading seem acceptable?

    Just been wondering if this sounds ok to anyone else. I have a PLX wideband on my 01 C5, the sensor is in one of the rear O2 spots, still stock exhaust. At idle and on the highway both if I have...
  5. I have a similar question. I already set my high...

    I have a similar question. I already set my high and low timing tables the same, and set my wot region to a flat value (14) and set my base spark in gear also (20). In my logs with the EST pids...
  6. Replies
    6
    Views
    2,321

    ? about autove inconsistency

    I'm just wondering if this is normal and I'm just looking too hard or if there might be an issue. I've been using the autove guide and have got to the end of adjusting, but I've noticed something...
  7. Replies
    5
    Views
    2,662

    I noticed a similar problem where if I selected 1...

    I noticed a similar problem where if I selected 1 pid in the filter and used 'exclude' it worked fine, but with more than 2 pid it would not filter anything. Inverting the comparisions and selecting...
  8. Replies
    19
    Views
    13,794

    If this is just a firmware issue, it wouldn't...

    If this is just a firmware issue, it wouldn't affect me if I haven't updated any firmware correct? I have only extracted the files and run the scanner/tuner, and uploaded calibrations to the...
  9. Replies
    2
    Views
    2,238

    Well, I installed M$'s updates and rebooted and...

    Well, I installed M$'s updates and rebooted and now it doesn't do it anymore. Sorry for the false alarm.
  10. Replies
    2
    Views
    2,238

    Dashboard guages issue

    I was setting up a dashpage from scratch and was putting in a digital guage for KR. I resized the sections to give the value section most of the area, but it still stayed at 12pt font even with...
  11. Replies
    7
    Views
    5,353

    Man, you document things like a champ! Good werk.

    Man, you document things like a champ! Good werk.
  12. Replies
    14
    Views
    5,449

    GDI. I'm a retard. I was only setting the filter,...

    GDI. I'm a retard. I was only setting the filter, not applying. Hooray for not reading the instructions.:doh2:
  13. That is pretty damn cool. Nice work.

    That is pretty damn cool. Nice work.
  14. Replies
    132
    Views
    69,668

    For this part are you supposed to force OL, or...

    For this part are you supposed to force OL, or stay in CL?
  15. Replies
    14
    Views
    5,449

    Is that ok to use with my v1 cable?

    Is that ok to use with my v1 cable?
  16. Replies
    14
    Views
    5,449

    I'm having a problem with filters that might be...

    I'm having a problem with filters that might be similar. When I have a log open and am looking at the "B" dashboard (the generic chart one) and press ctrl-alt-enter to open the filter dialog, select...
  17. Can v1 commercial version fully program a new pcm?

    Meaning, if I got a blank pcm, could my commercial v1 cable that can do os and calibration uploading, make this pcm usable? I have found that the tunercats product can, but I'm not sure if moret han...
  18. Replies
    1
    Views
    2,082

    Normal/Performance/Hot/Cruise modes

    What are they? What're the criteria for determining which column the PCM uses? Is it related to http://forum.efilive.com/showthread.php?t=2643&highlight=performance+mode this post, as in can you wire...
  19. Looking for a 01 auto 3.15 gear vette stock cal file

    Checked holdencrazy, but it looks like an 01 auto vette is the only stock file not there. :nixweiss: Just trying to make sure all the tranny values are stock as I haven't messed with an auto before....
  20. Replies
    4
    Views
    3,389

    So what did it do? :Eyecrazy: :D

    So what did it do? :Eyecrazy: :D
  21. Replies
    1
    Views
    1,525

    Thought about EFILive for a PDA/PocketPC?

    Just wondering if that has crossed the development brainstorming table. I think there was a version of autotap that ran on PDAs? How cool would that be to scan with a PDA phone while you're driving...
  22. Replies
    0
    Views
    2,157

    ETC help on shifts please.

    What tables do I need to adjust to lessen the throttle closing on shifts? Everytime it shifts the throttle closes down to almost 60% then opens back up, most of the time not getting to 100% before...
  23. Replies
    10
    Views
    4,366

    Just another quick question: The 98 vettes still...

    Just another quick question: The 98 vettes still have the incompatible pcm also correct? They didn't get a one year jump or anything like the ls1?
  24. Replies
    10
    Views
    4,366

    Yeah, just found out on tech.

    Yeah, just found out on tech.
  25. Replies
    10
    Views
    4,366

    In that case, has anyone put a newer pcm in a 98?

    In that case, has anyone put a newer pcm in a 98?
Results 1 to 25 of 26
Page 1 of 2 1 2