Search:

Type: Posts; User: killerbee; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    1,813

    Mitch what you want is possible if it is an...

    Mitch what you want is possible if it is an medium duty 06-07 5-speed, but not practical to try and do it with your TCM. It requires a TCM swap, a service we provide. Your TCM cannot be converted...
  2. Replies
    7
    Views
    3,989

    I ran into a new snag on the ever changing...

    I ran into a new snag on the ever changing TIS2WEB protocols. It appears to be no longer possible to bench program an LML ECM ONLY (2016 in my case). This is not about an offboard programming error...
  3. I am pretty sure the scanner is not license...

    I am pretty sure the scanner is not license specific.
  4. Replies
    3
    Views
    1,484

    [QUOTE=Blackdiamond;254707]Tried getting a stock...

    [QUOTE=Blackdiamond;254707]Tried getting a stock read off an 05 lly and got a communication error. Truck had no communication from ecm what so ever but everything else was reading. Customer had a...
  5. I can get it for you. But if you have a 2015...

    I can get it for you. But if you have a 2015 truck, are you sure you have an A50?
  6. Replies
    2
    Views
    2,038

    Thank you. I was not paying close attention to...

    Thank you. I was not paying close attention to everything but I will next time. Just using the cal flash unlock utility. Unlock the ecm after a few days, and full flash with another file in my...
  7. Replies
    2
    Views
    2,038

    Unlock script>>>>bricked ecms

    LB7 only. I have successfully unlocked 3 LB7 ecms using the script. What appears to happen is that the serial number is erased, becomes all zero's, rendering the ECM "not secured". Is this a...
  8. Replies
    2
    Views
    1,768

    In this truck, limp is almost always in 5th gear....

    In this truck, limp is almost always in 5th gear. Torque is what creates it. If you drop the tune 10-20 HP, and build an AL5 tune that prevents 5th gear below 2400 rpm (downshifts to 4th at higher...
  9. Replies
    2
    Views
    2,275

    I am assuming you have a MAF voltage calibration...

    I am assuming you have a MAF voltage calibration table? As well as MAF voltage PID. You will need to apply "known" rpm and boost values in a way to make that table accurate again. If you create a...
  10. Replies
    8
    Views
    2,391

    I empathize with the effort of reverse...

    I empathize with the effort of reverse engineering, it takes real dedication and gratification in immersion into the tedious. That said, with a diesel engine being basically a thermodynamic air pump...
  11. Replies
    2
    Views
    2,510

    The best way to recalibrate your gauge: 1. ...

    The best way to recalibrate your gauge:

    1. Run your truck out of fuel. Keep a container of diesel in the bed for when this happens.
    2. Head to service station with your log tool, parking your...
  12. I would ask the dealer. I doubt it is efilive...

    I would ask the dealer. I doubt it is efilive related. Coincidental failure possibly. What does your battery voltage read during idle?
  13. Replies
    0
    Views
    1,404

    Odd issue with TIS programming, 2015-16

    12658036 ECM, New

    This ECM was programmed for the customer using GM TIS. As it is a new ECM, I suspect that the 30 minute relearn was never performed. The following happened twice, both new...
  14. Have you considered getting the TCM tuned...

    Have you considered getting the TCM tuned properly? Since 06, the 6-speeds have never had an intelligent 4-5-6-5-4 shift pattern. 5-6 should never put the truck under 1800 rpm, nor drag down to...
  15. Replies
    3
    Views
    2,709

    If you need your ECM put back to factory file, we...

    If you need your ECM put back to factory file, we have a service for that.
  16. It's not an OS problem. If you want to send in...

    It's not an OS problem. If you want to send in the ECM's we can program them correctly to factory status.
  17. Replies
    2
    Views
    1,635

    Adrian, if you are just replacing the ECM, we...

    Adrian, if you are just replacing the ECM, we supply new and used replacements. You can send us the file you want in it, or we can install your factory file from the GM database. If you want to...
  18. Replies
    1
    Views
    1,860

    If you reload a stock tune, you may have your...

    If you reload a stock tune, you may have your answer.

    Also log your dsp voltage, as long as it is showing 5 values that make sense, you should be ok with another ecm.
  19. Yes, but it would be cheaper to swap ECM's

    Yes, but it would be cheaper to swap ECM's
  20. Replies
    19
    Views
    10,714

    To my understanding, as a slave device, the TCM...

    To my understanding, as a slave device, the TCM VIN coding portion is not important or relevant.
  21. Replies
    19
    Views
    10,714

    Is there some significance in using zeros???

    Is there some significance in using zeros???
  22. Replies
    4
    Views
    1,723

    I did find another OS with a positive value that...

    I did find another OS with a positive value that DOES makes sense. But so far all ...594 OS files I have show 0.0. I checked 4 files from 07-08. This only came up because I am working a P0101...
  23. Replies
    4
    Views
    1,723

    I am using imperial but 12628594. The bulk of...

    I am using imperial but 12628594. The bulk of the LMM fleet. I will check others also.
  24. Replies
    4
    Views
    1,723

    C0903, lmm maf limits for p0101

    In the factory files I have looked at this "P0101 Upper limit threshold" is set to 0.00.

    I would expect a P0101 every time. Does this make sense to anyone else? MAF tables max out at 64 lb/min,...
  25. Replies
    4
    Views
    3,300

    It depends. We may be able to restore it...

    It depends. We may be able to restore it affordably. If this is not convenient then the quickest way is probably to purchase one programmed.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4