Search:

Type: Posts; User: 2ktransam; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    5,915

    How much to repair both pcm's? I tried to pm you...

    How much to repair both pcm's? I tried to pm you and called.
  2. Replies
    8
    Views
    5,915

    That is possible. I was changing to a 28" tire...

    That is possible. I was changing to a 28" tire for the track so I was adjusting tire size and shift points. If that's the case, is it recoverable? I can post up the file later.
  3. Replies
    2
    Views
    2,537

    Never mind. I forgot to do the segment swap...

    Never mind. I forgot to do the segment swap since it was out of a t56 car. I think it is good now.
  4. Replies
    2
    Views
    2,537

    Transmission in limp mode after PCM swap

    I bricked two pcm's which I covered in another post so I tried my last licensed PCM in the car which has a different operating system. It has the same cos3 in it but it is a 01 opp system vs 02 so...
  5. Replies
    8
    Views
    5,915

    2 bricked pcm's please help

    I made transmission setting changes to my tune and loaded it and it bricked the PCM. It ran all the way through and said flash completed successfully. When I hit OK my fuel pump went crazy and it...
  6. Replies
    1
    Views
    11,788

    V1 license purchase

    I purchased a v1 license on Thursday evening on the website and I haven't got a reply yet. How long does it normally take? I have a budy that drove three hours to do a turbo setup and now I don't...
  7. Replies
    1
    Views
    2,624

    Low Impedance injector?

    I'm getting ready to tune my buddies turbo car and he has 127lb low impedance injectors with a driver box. I have never tuned low impedance injectors so what do I need to do with the injector...
  8. Replies
    13
    Views
    7,902

    That worked. Thanks Joecar. Not sure how I...

    That worked. Thanks Joecar. Not sure how I found that the last time.
  9. Replies
    13
    Views
    7,902

    PLX Wideband doesn't match?

    I have a couple of PLX widebands and both of them read about 3 to 5 tenths different from the gauge to the efilive software. How do I go about fixing this problem? In the older software I found the...
  10. Replies
    4
    Views
    3,311

    Got it figured out. Thanks

    Got it figured out. Thanks
  11. Replies
    4
    Views
    3,311

    Do you have to do anything specific to overwrite...

    Do you have to do anything specific to overwrite a HPtuner file? Could this just be a problem with the serial number?
  12. Replies
    4
    Views
    3,311

    Seirial number 00000000 and locked pcm?

    I just bought a s10 with a lq4 swap and the pcm was tuned by someone else. I think it may have been done by Current Performance Wiring which is a company that makes most of the swap parts for these...
  13. I'm having the same problem with my turbo truck. ...

    I'm having the same problem with my turbo truck. I have the motron 60's and my ve table has always been screwed up from having the wrong injector settings. I would like to get the injector tables...
  14. Replies
    4
    Views
    3,424

    I have looked through a lot of tunes and the 99's...

    I have looked through a lot of tunes and the 99's already have extremely agressive timing tables. The stock table is set to 28 degrees at wot except for a dip at peak torque. I'm going to play with...
  15. Replies
    4
    Views
    3,424

    Tuning stock corvette?

    I just bought a 99 c5 that has catback, gutted cats and intake. I'm throwing it on the dyno tomorrow to get a baseline and do a little tuning before I start modding. I'm used to tuning my 402...
  16. Replies
    9
    Views
    6,104

    I'm not sure. I will have to log it tomorrow and...

    I'm not sure. I will have to log it tomorrow and see.
  17. Replies
    9
    Views
    6,104

    I changed the cylinder volume and it didn't...

    I changed the cylinder volume and it didn't affect my fuel settings at all. Weird?
  18. Replies
    9
    Views
    6,104

    0.592703 I noticed that my cylinder size is...

    0.592703

    I noticed that my cylinder size is set for the 5.3L still. Could that cause this? My AF is good everywhere else but my VE is overstated to compensate for the cylinder size that I forgot...
  19. Replies
    9
    Views
    6,104

    Sorry, I guess I should give some info on my...

    Sorry, I guess I should give some info on my truck.

    01 silverado
    6.0L swap
    turbo
    z06 cam
    60lb injectors - motrons
  20. Replies
    9
    Views
    6,104

    Weird decel problem?

    I have a weird lean condition when I let off the throttle in my truck and start to decelerate. I'm running speed density in open loop and dfco is turned off for tuning purposes. The only way I can...
  21. Replies
    0
    Views
    2,202

    M6 to 60e swap with COS3 & SD

    Hello guys, I just wrapped up my auto swap and I can't figure out the tune swap. The guy that used to tune my car upgraded me to SD using COS3 02020003 and what looks to be an 2002 OS #1221256. I...
  22. Replies
    0
    Views
    2,487

    M6 to 60e swap with COS3 & SD

    Hello guys, I just wrapped up my auto swap and I can't figure out the tune swap. The guy that used to tune my car upgraded me to SD using COS3 02020003 and what looks to be an 2002 OS #1221256. I...
  23. Thread: B3647 help?

    by 2ktransam
    Replies
    3
    Views
    3,415

    B3647 help?

    I am trying to Auto Ve my truck to work with speed density and I am having issues with my commanded AFR. I have B3647 set to run a little leaner at cruising levels and .78 lambda in for the upper...
Results 1 to 23 of 23