Ok found that the USB plug on the cable, not the FS unit, is loose as well. It appears that the guy I bought this from must have had it stuff up against something and had the cable bent fairly close...
Type: Posts; User: 99ss; Keyword(s):
Ok found that the USB plug on the cable, not the FS unit, is loose as well. It appears that the guy I bought this from must have had it stuff up against something and had the cable bent fairly close...
http://www.moates.net/documentation.php?documentation_id=34
Question ... after is warms up it wants to run lean ..like 15.3-15.8 just at idle. How can I correct that? Its 12.2 at startup WOT and part throttle is ok, not lean, maybe a little rich but not...
More info: I found the long with standing TPS issue that kept throwing the p0121 code. I measure resistance on the circuit and found that the ground for the TPS signal has like 20ohms so there is an...
I wasnt logging before. The wideband was connected first. I'll add the VSS pid in there and see what it shows. If its normal I'll take it for a ride. The laptop is plugged in via ac cord to the...
Ok followed Ira's instructions and I'll post the log. I havent tried the battery test yet, the log is interesting enough. I dont have anything connected to annalog 1 and 2 but they show 2.5
...
Where do I connect the battery on FlashScan?
Ira thinks it might be software so I'm going to follow his steps as well. He's having me delete EFIlive and re-install it.
Ok got back to basics on a few things. I first checkd the ecu grounds to the battery and they are fine. I knew I had a TPS issue long with standning so I started there. the +% and ref signal were...
I connect to the RR ok thru the usb but when I try to connect using the flashscan it doesnt show the red and yellow button options to record? which controller do I select, same as for my ecu?
Cool, waiting for it. Its 1:22 pm here now. This is driving me nuts. Either the ecu took a hit or the flashscan unit or I really do have a bad short somewhere that I cant find. lol take your...
Yea I sent them an email and Andrew got back to me. He said he sent an email and I should be getting an email soon.
I did find 1999-2002 ecu's on ebay for about $125 delivered so I wont have to...
trying to get over the licensing hump with the RR. When I enter the RR serial number it reverts my eflilive back to demo version
I tried a new battery and full flash but to no avail. I cant see...
The ecm may have been disconnected while the battery was connected, I'm not real sure. If the ecm is in a state how do I get it back or can I? I've always had trouble with throwing p0121 codes. Not...
Ok ran new grounds didnt help. Pulled the plug for the VSS and it still says it's doing 30mph while sitting there.
It didnt have the strange misfire counts before I reflashed, not sure about...
Ok this is the new plan. I'm going to chase down the electrical problems causing the wrong values.
TP, IAT, and VSS and MAP are all on the same ecm connector. (according to my WBC software my TPS...
validated then started it here is the log. car sounds like crap too, you can hear it missing
reflashed.. checked voltage and the same
voltage was 13
I'll wait and see what you say. I'm about...
I do the re-cal only flash and I wait until the 15 second timer has expired and usually a little longer.
I'll go connect and validate. Not sure where to edit vin os and trans but I'll find it..lol
I have the v1 flashscan pluged via usb into my laptop. I have the wideband wired in to the flashscan on the analog side middle is ground and the one furthest away from the other output jack is what...
Whats really weird is when I first started all this I was getting slight misfires on all cylinders. Then I recalibrated and it was maybe a little lean and I got all 50 counts on all cylinders except...
I have a dynojet wideband commander not an lc1
What LED?
I've been logging using my laptop
I pulled a couple plugs to look at them and they were black again. They cleaned off easily though.
I dont think its lean, as soon as you see the log you might agree. I cna pull the rails it's not a huge job. The first log I only had a few and then I had them everywhere and always the same count...
Here it is. I burn a hole in 3 pistons did I? I mean theres now way right, we'd
see other stuff and it wouldnt run good right? All the spark plugs looked the same black
changed them and re-flashed new IFR and same thing as far as the misfires 6,7 and 8. I'm about to shoot myself now. I'll post the log as soon as I get back. 2 hrs
Ok think I found the misfire issues. Pulled one of the plugs that was reporting and it's as black as black can be. I'll get a new set on the way. with the new IFR calcs I shouldnt have an issue. It...