Hi folks,
if I set on the E78 the H0156 "Speed limiter source" to PCM - will this bring me full control over the
limiter via PCM or are still any other modules involved or affected?
I have to...
Type: Posts; User: Treurentner; Keyword(s):
Hi folks,
if I set on the E78 the H0156 "Speed limiter source" to PCM - will this bring me full control over the
limiter via PCM or are still any other modules involved or affected?
I have to...
Sorry, these files are in Tunercat file format. But the tables from TCM that you mentioned
are all alredy maxed out and set to 663,8 ftp.
Next week the car will be here again, and we will log the...
No Changes on this...
regardless of the torque or throttleangle.
It ALWAYS shifts down form 6->5 at 230 km/h
and if I lift off the throttle it does NOT shift down to 6
if the speed is over...
Hi,
has anybody tried to use an Vette based OS 24243170 instead of a Camaro based OS 24249179 to solve this T43 downshift issue?
Kind regards
Marco
Hi,
that was the right recommendation,
first i used the old winxp toshiba stack with some issues but then
I tried the updated Toshiba stack for win7, 32bit - and it works perfect!
Filename:...
Hi,
does anybody got it work and how it was done?
I personally can establish a virtual com port connection to roadrunner (Blueradios adaptor) under Win7 (default as pw for linking the BT...
Hi Joecar,
these are the the values:
Parameters Value
{B1901} Max Allowed Engine Torque 867.010558 Nm
{B6601} Axle Torque Limiting Disable
{B6615} Max Torque, Front Axle ...
Hi,
i recently saw on part throttle acceleration, that the transmission torque limits are pulling around 15° timing until the TCC is locked, {GM.EST_XMSN_DMA} is logged, see attached file....
Ok - finally I can give the solution and the answer is:
NO it will not work in boosted applications - IF...
you have (or get) turbulent airflow.
This may caused by an improperly installed...
Hi,
finally found what happend:
the 0038a file was corrupted from EFILive Tuning Tool 7.5.6(109) itself.
No checksum calculation is made when the file is saved. Regardless if it´s under the...
Hi,
any recommendations for a E40 PCM in Corvette C6?
After a flawless BBF I got a corrupted data segment with wrong checksum after reading the PCM (that was in in non start condition after the...
Hi Joe,
many thanks or the explanation :cheers:
Kind regards
Marco
Anyone using the #12576410 or #15865791 Ls3 LS7 etc... Powrmax 100 mm Maf sensors? Any known problems?
My Maf frequency is in the range of 600 Hz at idle (427cui) what is 300% off from the expected...
Why not use the 12221588 OS - what was issued later? Any known disadvantages?
Kind regards
Marco
Hi,
I fixed it!
Ira wrote me:
Right near the USB connector is an 8 pin chip, usb6b1, it will
usually have a hole in it where it exploded. It's almost always that
part. Once it was also...
Hi Ross,
I contacted Ira (he replied very quick) and bougt the (propably defective) USB protection circuit today. We will se what happens after the swap.:confused:
I ´ll keep you posted.
...
Hi.
I have exactly the same problem as boosted GMC described.
Mine is fine too - plugged in OBD2 and can communicate with the laptop as well.
With the USB-laptop connection only it trys to power...
Hi Steve,
thank you for pointing me to that table. I already was aware of this possibility when I did the update from 97/98 PCM to the 411 PCM.
Under WOT it gave me 6 extra degrees of (unwanted)...
Hi,
for those who have never seen lean cruise working I added a log where you can find a commanded AFR above 14.63 :).
After using the merged patch from Joecar for that OS it was not working. I...
Hi,
my email is marco.babatschew@versanet.de
Many thanks!:cheers:
Marco
Hi,
can you post your ini file to see what pids are working (I have a S15 SLT -4.3 Vortec)? I would be happy if I can use BBL on that car too:cucumber:
Many thanks in advance!
Marco
Hi,
could this issue be solved with the actual V8.1.1.33 and
Is the AEM now correcty displayed?
Kind regards
Marco
Hi folks.
:help::help::help:
like the title says - PCM is urgent needed.
I can Paypal asap.
Shipping directly to Craig Moates for Roadrunner conversion.
I think he is out of cores :bawl:...
Hi Paul,
will the L31 controller (Vortec engine) be supported for BB logging with DMA pids like Knockretard? I can do BB logging with the P12 files and modified pid selection (mostly like LS1)...
Hi Paul,
maybe I have the same problem.
I did a clean install (on a new PC) of V 7.5 and unzipped the latest BB update over the existing files. The previously logged BB files seem corrupted...