Search:

Type: Posts; User: joecar; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    12
    Views
    366

    You may have to Validate Pids. Also, instead...

    You may have to Validate Pids.

    Also, instead of E38.AFRATIO_DMA, try SAE.LAMBDA, and if it works use this.
  2. Replies
    4
    Views
    102

    Which PCM/ECM (I take it it is LS1B)...? Are...

    Which PCM/ECM (I take it it is LS1B)...?

    Are you obtaining the wideband lambda/EQR/AFR signal from analog voltage or from serial comms...?

    Take a look in the calc_pid.txt file under "1. Setup...
  3. Replies
    10
    Views
    2,993

    +1 no problem.

    +1 no problem.
  4. I'm reading thru this thread (sorry I'm running...

    I'm reading thru this thread (sorry I'm running behind due to work).
  5. Replies
    28
    Views
    26,186

    Sticky: I'm slowly reading thru your posts... please bear...

    I'm slowly reading thru your posts... please bear with me.
  6. Replies
    8
    Views
    2,307

    Hi John Done, This forum is for EFILive users....

    Hi John Done,

    This forum is for EFILive users. Please tell me your vehicle's engine RPO, and I'll let you stay...
  7. Replies
    28
    Views
    26,186

    Sticky: If you change the shift points, you don't need to...

    If you change the shift points, you don't need to do the adaptive relearn.

    Be careful in adjusting the shift pressures (!!!)... leave them alone.
  8. Please post some logs.

    Please post some logs.
  9. Post the ECM file also.

    Post the ECM file also.
  10. Is the engine stock...? What other mods...

    Is the engine stock...?

    What other mods (engine, trans, vehicle) besides the 22" rims...?
  11. I'm looking thru your files.

    I'm looking thru your files.
  12. There's a lot of info there, I have to read thru...

    There's a lot of info there, I have to read thru it slowly, I'll get back in a few days.
  13. Replies
    6
    Views
    246

    Post your TCM file.

    Post your TCM file.
  14. Replies
    2
    Views
    259

    Post your tune file.

    Post your tune file.
  15. Replies
    151
    Views
    117,985

    Sticky: Measure line pressure at the tap on the side of...

    Measure line pressure at the tap on the side of the case, see what it does during the shift.

    Also log GM.TFMPRS, GM.GEAR and the other pids (VSS, RPM, ETC or ETCTP, MAP, MAF, ECT, TFT, TCCMODE)...
  16. Replies
    17
    Views
    5,428

    On my Win7 PC, S&T and EE can't connect to...

    On my Win7 PC, S&T and EE can't connect to FSV3... this pops up:
  17. Replies
    4
    Views
    1,246

    In particular, look at details regarding MAF, VE,...

    In particular, look at details regarding MAF, VE, LTFT, IFR.
  18. Replies
    4
    Views
    1,246

    Start here: Summary-Notes...

    Start here: Summary-Notes
  19. Sounds like it's riding the spark advance table....

    Sounds like it's riding the spark advance table. Post your tune and log.
  20. Replies
    2
    Views
    250

    EFILive (and HPT) can only flash the controller...

    EFILive (and HPT) can only flash the controller if it already has a calibration in it (i.e. not blank).
  21. Replies
    1
    Views
    149

    Post your tune file.

    Post your tune file.
  22. What did you figure out...? ( we're hoping...

    What did you figure out...?

    ( we're hoping each post contains something of value so that it can help the next person )
  23. Thread: Scan setup

    by joecar
    Replies
    5
    Views
    321

    SAE.LAMBDA may be commanded EQR or commanded...

    SAE.LAMBDA may be commanded EQR or commanded Lambda (i.e. 1/EQR)... you have to look at the logged waveform to make sure (i.e. during PE EQR should go above 1.00, and Lambda should go below 1.00).
    ...
  24. Replies
    4
    Views
    220

    I dug thru my old old archives, l found this...

    I dug thru my old old archives, l found this (attached)... look thru it and choose what you need.
  25. Thread: SAE.MAP Issue

    by joecar
    Replies
    2
    Views
    185

    Ok, good you got it sorted out :cheers:

    Ok, good you got it sorted out :cheers:
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4