Search:

Thanks!

Joecar-

I am getting my new valvetrain kit tomorrow and will try to get it installed in the next week. in the meantime, I am configuring a Toughbook to be the dedicated tuning/diagnostic garage...

Yes it is... ive done what i could but i think i may take a few more logs of just WOT pulls and paste the WOT section in as i think my part throttle driveability area is pretty well sorted out. ill...

okay, so ive finally gotten a break here...



throttle response has not seemed to change much. as of this point I have not reenabled the VE table or checked it by failing the MAF. however just...

Also I ordered a screened Delphi 85mm maf and the bits to go with it on a whim just in case my descreened stock maf was causing a problem...
Is it worth Installing this on a ~500 rwhp car and

I...

Joecar- thanks for all your help on this. I have yet to run speed density to verify the ve table so I cannot comment yet on feedback for calc.vet until I am done with the tuning, but I most certainly...

Joe,

I am running a 98 ECU/car so I do not have GM.DYNAIR..

Also I do not have GM.DYNCYLAIR selected, Nor do I have CALC.CYLAIR in my logs... all I have is GM.CYLAIR_DMA. is this all a...

attatched is a screenshot of my calc.vet derived VE table... there is no computer smoothing done, however I have been selecting individual cells and increasing by .5% at a time to smooth and bring up...

21486

21485

Attatched log

Thanks Joecar… I’ve replied to your questions below. Im really unsure of how to proceed at this point.. ive added exactly what im doing below in hopes you can point me in the right direction


I...

Ive been doing calc.vet and have come across a few questions...

for reference, this is a stock cubic inch ls1, trickflow 215 cnc heads, vengeance vrx5 camshaft (236/238 .601/,605 113 LSA),...

Well the brand new innovate wideband is giving me e8 error codes if I step into it too hard. The readout jumps all over the place and "hangs" on a number then will usually begin reading again after I...

Oh... i see... Build number is 323

I think everything looks good on the tutorial.... I was able to follow along and made my first adjustments to the tune yesterday. short of me not seeing the...

Thanks for all your help Joecar! I think I might actually get this to work...

my version is 7.5.10

okay, so what ive done is this.... taken a log, gone to maps tab, clicked "open a new map definition for display", found CALC.VET g_K_kPa.map, selected that, gone to "edit map properties" and I...

well, I looked through everything again... I must be missing something... can I get a link with directions on where to find the instruction for preparing the map? ive followed what I can gather and...

Joecar,

Yup... That would be the problem. I've been over the tutorial and the advanced notes dozens of times but I must be missing that part. I thought the copy/paste was only mentioned in...

21422

Last resort thought as well... Ceramic long boot plug wires are also available from accel

I just bought the lt1 coil ends and used a universal set of wires that I could cut to length. Amazon has the lt1 ends, universal wires(Taylor for sure, maybe others), and dei products all on prime. I...

Also be sure you use genuine dei titanium... It's expensive but the china clones are nothing more than a standard fiberglass unit and only offer 1/2-2/3 the protection in my experience. Ive used both...

Are you running lean? If not it may just be the nature of the beast. I don't have the experience to gauge your egt however my n/a lsx burns wires quite rapidly. My fix was to build my own wires using...

Okay, so I've gotten everything set up, pids validated, map filter parameters preset, etc.etc. and am ready to start logging. Working with a 98 and v1. Have followed tutorial to the T with wideband /...

I lied. recieved a registration code, and issue date, entered both into efilive, still same results. waiting on tech support to respond.

Joecar - i have used builds 282, 283, 286? (july pre...

Soooooo... Problem is i changed laptops over a year ago and had never re entered registration number. :bash: somehow i figured authentication code was the same. Emailed support with my serial number...