Search:

Type: Posts; User: miguelc; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    1,873

    A6 standalone wiring tap shift?

    Greetings do you know how could I get it to work on truck OS

    thanks
  2. Replies
    5
    Views
    6,525

    did you get the A6 tap shift to work?? I have a ...

    did you get the A6 tap shift to work?? I have a truck wiring (2008 scalade)
  3. Replies
    0
    Views
    2,204

    vvt tuning, 400 cam form comp

    Greetings

    Im gonna start dealing with vvt, I ordered 400 cam ( 210 intake).. Do you have any pointer so I dont borke an engine and make the most power on the below 4000 rpm range?


    By the...
  4. Replies
    3
    Views
    2,968

    by the wa, since all stuff and calibration ......

    by the wa, since all stuff and calibration ... all hardware is form a 4WD silverado. Is there any way The ECU triggers the 4wd low signal? I got no body control module
  5. Replies
    3
    Views
    2,968

    Tps stays high on scanner, it evens launch hard...

    Tps stays high on scanner, it evens launch hard but shifts at low rpms
  6. Replies
    3
    Views
    2,968

    WOT shifts very low (2500 to 3000 rpm)

    Greetings form Mexico

    I did a e38 standalone on a Fox mustang. Car was running Ok and then it started to shift very low at WOT. The car always had a ISS code but worked OK. Do you know hoy I can...
  7. Replies
    1
    Views
    4,241

    L5 harrop supercharger goes lean???

    Greetings, I am tuning an L5 colorado.

    At 10000 hz the afr goes leaner and leaner, we swaped for a bigger fuel pump and a 58psi regulator. Now fuel pressure is constant at 58 psi and the AFR...
  8. by the way, wiring and ecu,tcm are form a 2007...

    by the way, wiring and ecu,tcm are form a 2007 silverado
  9. e38 standalone, starts and dies after 2 seconds max

    Hello everyone

    I disabled VATS, used a 100 ohm resistor on he black and yellow wire. the car was running, then took it to a 3 min ride.... after that the car only starts and dies and throws...
  10. e38 standalone, no power to MAP,ECT and alll 5volts form gray connector

    greetings

    How do I diagnose a faulty ECM? It seems that every sensor hooked up to the gray connector doesnt have a 5v supply, also tps reads 100... could you help me, my boss doesnt want to...
  11. Thread: t42, no ISS

    by miguelc
    Replies
    3
    Views
    3,295

    Thanks for your answer. I do own an interface....

    Thanks for your answer. I do own an interface.
    Could you please point me on what tables/ parameters to modify?
    Or is there some transmission files I can compare?
    Thanks again
  12. Thread: t42, no ISS

    by miguelc
    Replies
    3
    Views
    3,295

    t42, no ISS

    Greetings

    We plan to do an engine swap, since we got a 4l60 trans and a genIV engine. Do you have theTCM file to do this? or could you tell me a shop that works on this conversions?

    thanks...
  13. Replies
    0
    Views
    1,654

    p031 after dual walbros

    Greetings

    I just wired two walbros to the stock power line. It shows the code even I select no error reported and dissabled the code U0109

    do you have any idea what I could do? maibe a resistor?
  14. Replies
    0
    Views
    2,360

    please help me, code P0606

    Hi everyone


    We have done like7 trucks with 4l80, then two of them (they have lsx engines 427 and 454) are throwing this code out of nowhere.
    we tired using a new vcm and it didnt work
    ...
Results 1 to 14 of 14