Search:

Type: Posts; User: Brad Kimbler; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,715

    Only other thing to add is that they had the...

    Only other thing to add is that they had the heads off during the cam swap to put lifters in. I wouldn't think this was a problem other than moving wires around that go to knock sensors, they look...
  2. Replies
    6
    Views
    1,715

    Ok, well it won't let me do a crank relearn. ...

    Ok, well it won't let me do a crank relearn. From what I kn ow about the Gen3 stuff, if knock sensors are bad it won't allow a relearn. Maybe gen 4 is the same. I'll look into running a test on...
  3. Replies
    6
    Views
    1,715

    This issue reminds me of a LS1B computer where...

    This issue reminds me of a LS1B computer where the knock sensors were putting it in some type of engine protection mode. Customer did stat that directly after the cam swap the car didn't have power...
  4. Replies
    6
    Views
    1,715

    0/-2 degrees timing on cammed 2006 GTO

    I just had a 2006 GTO dropped off with a BTR stage 4 cam...at first start this car barely pulled into the shop. After first log I noticed that total ignition timing was in the -2 to maybe 2 degree...
  5. Replies
    2
    Views
    933

    Sorry, it is a E38..planning on E85 with a pt88...

    Sorry, it is a E38..planning on E85 with a pt88 turbo/forged ls3
  6. Replies
    2
    Views
    933

    ID1700 injectors

    Before I pull the trigger on these monsters, who all has had luck getting idle worked out with these. Can they be scaled with any issues? Thanks
  7. I will try it this weekend when he comes bac k

    I will try it this weekend when he comes bac
    k
  8. I think I just found it...When I increased the...

    I think I just found it...When I increased the rpm shift point I didnt increase B5401(ECT rpm limit) This makes sense as the 1-2 is set to shift at 6100rpm and the 2-3 shift set to 5750 ..only...
  9. Here is the log showing the Throttle TPS falls to...

    Here is the log showing the Throttle TPS falls to 30% during the 1-2 shift, no timing falls, just TPS
  10. Having issue deletin gECT torque Management during 1-2 shift

    Tuned 2003 GMC truck with a cammed 4.8. all was going well until we increased the 1-2 shift point then we noticed a big delay during the 1-2 shift, on the scanner it show TPS going from 99.6 down to...
  11. Replies
    23
    Views
    5,459

    13 vanes are worse about breaking, the extra...

    13 vanes are worse about breaking, the extra vanes are slots in the same diameter rotor as a 10 vanes, so 3 more slots thin out areas on the rotor...The main stress point is converter installed depth...
  12. Replies
    43
    Views
    10,618

    I just want to add I have both EFILIVE and...

    I just want to add I have both EFILIVE and HPTUNERS.. I strongly favor EFILIVE, it allows for such better turbo and SD tunes...Only reason I have HPtuners is because it supports V6 cars (3.8camaros...
  13. Replies
    23
    Views
    5,459

    Its hard to get a firm or hard 3-4 shift, I...

    Its hard to get a firm or hard 3-4 shift, I usually build 3-5 4l60es a month for 10-11 sec cars as well as stock builds..I totally block off the 3-4 accumulator and DOUBLE the valvebody feed, this...
  14. I got a cold start log, added a few pids I think...

    I got a cold start log, added a few pids I think might be helpful, Notice the desired airflow is 0.00 until 99F ECT, thats where rpms jump up ...during the 99F and colder are I have my foot on the...
  15. Yes sir, I wasn't watching it to see the value,...

    Yes sir, I wasn't watching it to see the value, I'll double check to see if its reading but it was in the intake
  16. Yes, Maf is gone and they cut the pigtail...

    Yes, Maf is gone and they cut the pigtail connector off, I can run another log and save it..
  17. 1998 Corvettte cold start issue (MAF DELETE related?)

    I received a 1998 corvette with not 3-4 in a 60e, I pulled the trans and rebuilt it, no issue, the customer then wanted to fix his cold start issue

    I Pulled the tune(no MAF on the car) and started...
  18. http://i251.photobucket.com/albums/gg304/silverz28...

    http://i251.photobucket.com/albums/gg304/silverz28camaro/efilivebug_zps71b753c7.png
  19. Please Help, Cannot use new V8 flashscan

    I purchased the V8 upgrade from an EFILive Dealer along with the LS1B stream, First I found it odd as it did not come with the LS1A stream as I believe its a given free stream by EFILive. I have...
  20. Replies
    6
    Views
    1,555

    My computer won't allow me to open the cax file...

    My computer won't allow me to open the cax file to change the hex. address, can I use this cax. file from post #8? Its suppose to be for the 1250003 os
    ...
  21. Replies
    6
    Views
    1,555

    Thank you for your reply , I did rename the cax....

    Thank you for your reply , I did rename the cax. for the 01 OS but how do I go about changing HEX location?
  22. Replies
    6
    Views
    1,555

    ID1000 are running rich at idle

    I have a ls2/4l60e with a PT88mm turbo on my 1988 dodge Ram...I bought the ID1000 injectors that came with all the data and downloaded a custom OS into my 2001 Camaro computer along with a CAX file...
  23. Questions about upgrading from V1 to V2

    I am wanting newer better tuning software that will allow me to do more vehicle such as the v6 camaros, E38, e40 computers, ETC. I mave several customers now that consistently change setups and...
  24. Replies
    6
    Views
    1,711

    tune file

    tune file
  25. Replies
    6
    Views
    1,711

    log file

    log file
Results 1 to 25 of 38
Page 1 of 2 1 2